- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1845 (Sanyo Electric Co.,Ltd.) PWM Current Control Stepping Motor Driver(PWM電流控制馬達驅動器) PDF資料下載
參數資料
| 型號： | LB1845 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | PWM Current Control Stepping Motor Driver(PWM電流控制馬達驅動器) |
| 中文描述： | PWM電流控制步進電機驅動器（PWM電流控制馬達驅動器） |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 136K |
| 代理商： | LB1845 |
Usage Notes
1.External diode
Since this IC adopts a system based on lower side transistor switching drive, an external diode for the regenerative
current that occurs during switching is required between V
BB
and V
OUT
. Use a Schottky barrier diode with a low
feedthrough current.
2.Noise filters
Since spike noise (see Figure 1) occurs when switching to the on state due to the external diode’s feedthrough current,
applications must remove noise from the SENSE pin with a noise filter (Cc, Rc) between the E pin and the SENSE pin.
However, note that if the values of Cc and Rc are too large, the SENSE voltage rise will be slowed, and the current
setting will be shifted towards a higher current level.
3.V
REF
pin
It is possible to change the output current continuously by continuously changing the V
REF
pin voltage. However, this
voltage cannot be set to 0 V. The V
REF
pin input impedance is 26 k
(±30%) when V
REF
is 5 V. Since this pin is used
to set the output current, applications must be designed so that noise does not appear on this pin's input.
4.GND pin
Since this IC switches large currents, care must be taken to avoid ground loops when the IC is mounted in the
application. The section of the PCB that handles large currents should be designed with a low-impedance pattern, and
must be separated from the small signal sections of the circuit. In particular, the ground for the sense resistor Re must
be as close as possible to the IC ground.
5.Operation in hold mode
There are cases where a current somewhat larger than the current setting may flow in hold mode (light load mode).
Since this IC adopts a lower side switching, lower side sense system, the emitter voltage falls and the sense voltage
goes to 0 when the switching state goes to off. The circuit then always turns the output on after the toff period has
elapsed. At this time, due to the light load, the existence of the time td, and the fact that the output goes on even if the
output current is higher than the set current, the output current will be somewhat higher than the set current.
Applications should set the current setting somewhat lower than required if this occurs.
6.Function for preventing the upper and lower outputs being on at the same time
This IC incorporates a built-in circuit that prevents the through currents that occur when the phase is switched. The
table lists the output on and off delay times when PHASE and EANBLE are switched.
7.1-2 phase excitation and the double 1-2 phase excitation control sequence
To reduce the vibration that occurs when the motor turns, this IC supports 1-2 phase excitation and double 1-2 phase
excitation by using the output current setting digital input pins I0 and I1 without changing the V
REF
pin voltage. Tables
1 and 2 list that control sequence, and Figure 2 and Figure 3 present the composite vector diagram for this sequence.2.
Noise filters
No. 5505-5/7
LB1845
Sink side
Source side
When PHASE is switched
On delay time
10 μs
9 μs
Off delay time
1.5 μs
3 μs
When ENABLE is on
On delay time
9 μs
9 μs
Off delay time
1.5 μs
6.5 μs
No.
Phase A
Phase B
PH1
I11
I01
Current value
PH2
I12
I02
Current value
0
0
0
0
1
*
1
1
0
1
0
0
1
2/3
0
0
1
2/3
2
*
1
1
0
0
0
0
1
3
1
0
1
2/3
0
0
1
2/3
4
1
0
0
1
*
1
1
0
5
1
0
1
2/3
1
0
1
2/3
6
*
1
1
0
1
0
0
1
7
0
0
1
2/3
1
0
1
2/3
Table 1 [1-2 phase excitation] 1/2 step
ENABLE1 = ENABLE2 = 0
相關PDF資料 |
PDF描述 |
|---|---|
| LB1846M | Low-Voltage/Low Saturation Voltage Type Bidirectional Motor Driver(低電壓/低飽和電壓型雙向電機驅動器) |
| LB1846 | Low-Voltage/Low Saturation Voltage Type Bidirectional Motor Driver |
| LB1847 | PWM Current Control Type Stepping Motor Driver(PWM電流控制馬達驅動器) |
| LB1851M | 22.1 OHMS 1% 1/2 WATT MF RESISTOR AXIAL |
| LB1854 | Three-Phase Brushless Motor Driver IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1845_06 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Controlling Stepping Motor Driver |
| LB1845_12 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Controlling Stepping Motor Driver |
| LB1845DAZ-XE | 制造商:ON Semiconductor 功能描述:STEPPING MOTOR DRIVER - Ammo Pack 制造商:ON Semiconductor 功能描述:Motor / Motion / Ignition Controllers & Drivers STEPPING MOTOR DVR 制造商:ON Semiconductor 功能描述:FNFLD / STEPPING MOTOR DRIVER |
| LB1845-E | 功能描述:馬達/運動/點火控制器和驅動器 PRINTER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1845L-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。