- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1824 (Sanyo Electric Co.,Ltd.) Power Brushless Motor Driver for OA Equipment PDF資料下載
參數資料
| 型號： | LB1824 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Power Brushless Motor Driver for OA Equipment |
| 中文描述： | 功率無刷電機驅動的辦公自動化設備 |
| 文件頁數： | 9/9頁 |
| 文件大小： | 134K |
| 代理商： | LB1824 |
P = P2 = 0.19 W
At start time:
P = P1 + P3 + P4 + P5 = 6.51 W
(for an output on duty of 100%)
16.Techniques for measuring the IC temperature increase
Measurement with a thermocouple
When using a thermocouple to measure the IC temperature, the thermocouple should be attached to a fin. While
this measurement technique is simple, it is subject to large measurement errors if the IC is not in a stable heat
generation state.
Measurement using the characteristics of an IC internal diode
We recommend using the parasitic diode between INT.IN and GND internal to the IC. (According to our data, I
D
= 1 mA with about
1.8 mV/°C) Remove the external resistor when making the measurements.
17.Servo constants
When calculating the servo constants, they will be heavily dependent on the motor actually used. Since experience is
generally required, these constants should be determined by the motor manufacturer. We can provide the IC
characteristics data required for the servo constants calculations as well as frequency characteristics simulation data
for the filter constants set by the motor manufacturer.
If the resistor connected between DOUT and INT.IN (R10) is too small, C8 and C9 are too large, and R10 is too
large, speed errors will be likely to occur due to the speed discriminator cutoff current and the integrator input
current. Therefore, a 10 to 100 k
resistor should be used. If the resistor connected between POUT and INT.IN (R8)
is too small, the PLL system influence will become too large and the in-phase pull-in to locking will get worse.
Therefore, do not make this value too small. (We recommend 1 M
when R10 is 75 k
.) First set the constants just
for the speed discriminator system (R9, R10, C8 and C9) and then set the R8 value for the PLL system.
LB1824
No. 4264-9/9
This catalog provides information as of September, 1997. Specifications and information herein are subject to
change without notice.
I
No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
I
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
I
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
相關PDF資料 |
PDF描述 |
|---|---|
| LB1825 | Three-Phase Brushless Motor Driver |
| LB1830 | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1830M | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1831M | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1832V | Low-Saturation 1.5-Channel 3 V Drive Bidirectional Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1825 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver |
| LB1830 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1830M | 制造商:Panasonic Industrial Company 功能描述:IC |
| LB1830M_11 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Low-Voltage, Low-Saturation Bidirectional Motor Driver |
| LB1830MC | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Bidirectional Motor Driver |
發布緊急采購，3分鐘左右您將得到回復。