- 您現在的位置：買賣IC網 > PDF目錄358744 > LB11920 (Sanyo Electric Co.,Ltd.) Three-Phase Brushless Motor Driver for Office Equipment Applications PDF資料下載
參數資料
| 型號： | LB11920 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Three-Phase Brushless Motor Driver for Office Equipment Applications |
| 中文描述： | 三相無刷電機驅動應用辦公設備 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 103K |
| 代理商： | LB11920 |
LB11920 Function Description
1. Output drive circuit
This IC is of a direct PWM drive type that suffers less power loss at the output.
On the basis of the signal (“H” level for OFF and “L” level for ON) entered in the PWMIN pin, the lower output Tr
performs PWM switching, causing change in the motor drive power.
To control by means of the DC voltage, apply the voltage to the TOC pin (in this case, the PWMIN pin should be in
the “L” level input condition). The TOC pin voltage is compared with the oscillation voltage of PWM pin,
determining the duty. As the TOC pin voltage is lower, the output duty increases.
2. Hall input signal
For Hall input, entry of the signal whose amplitude is larger than the hysteresis width (50 mV max) is necessary.
Considering effects of noise and phase delay, entry of the amplitude of 120 mVp-p (at differential input) or more is
recommended.
When noise causes disturbance in the output waveform (at phase switching) or in the HP output (Hall signal three-
phase composite output), insert a capacitor, etc. as near as possible to the pin between inputs to prevent such effects.
The Hall input is used as a signal for judgment of the input of the motor lock protection circuit. Though it is designed
to ignore noise to a certain extent, due attention should be paid to check for incorrect operation of the protection
circuit.
Both upper and lower outputs are OFF when all three phases of Hall input signal are in the common-mode input
condition.
When the Hall IC output is to be entered, entry of 0 - V
CC
can be made for another single-side input by fixing either
one side (+ or –) of input to the voltage within the common-mode input range with the Hall element used.
3. Current limiting circuit
The current limiting circuit performs limiting with the current determined from I = V
RF
/Rf (V
RF
= 0.5 Vtyp, Rf:
current detector resistance)(that is, this circuit limits the peak current).
The control operation functions to reduce the on state duty of the output and thus reduce the current.
Switching during current limiting is made on the basis of the frequency oscillated with the PWM pin.
The PWM frequency is determined from the capacitance C (F) of capacitor connected to the PWM pin.
f
PWM
≈
1/ (50000
×
C)
The PWM frequency of 15k to 25 kHz is recommended. As PWM oscillation is used also as a clock signal of the
internal logic circuit, its oscillation is necessary even in the application where current limiting is not needed.
No. 7229-8/10
LB11920
Continued from preceding page.
Pin No.
Pin
Function
Equivalent circuit
Hall amplifier input.
IN+ > IN– is the input high state, and the reverse is
the input low state.
Connect a capacitor between the IN+ and IN–
inputs if there is noise in the Hall sensor signals.
18
17
20
19
22
21
IN1+
IN1–
IN2+
IN2–
IN3+
IN3–
VCC
300
19
300
22
20
18
23
21
SUBGND pin to connect to GND1 that is GND of
the control circuit
23
GND3
NC pin that can be used for wiring.
4
27
NC
Continued on next page.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11921T | Monolithic Digital IC Three-Phase Brushless Motor Driver |
| LB11922 | MONOLITHIC DIGITAL TRANSISTOR |
| LB11946 | PWM Current Control Stepping Motor Driver |
| LB11948T | Monolithic Digital IC PWM Constant Current Control 1-2 Phase Excitation Stepping Motor Driver |
| LB11970FV | Monolithic Digital IC For Fan Motor Single-phase Full-wave Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11920_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For OA Products Three-Phase Brushless Motor Driver |
| LB11920-E | 功能描述:馬達/運動/點火控制器和驅動器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11921T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC Three-Phase Brushless Motor Driver |
| LB11921T-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11921T-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 PWM STRUCTURE PRE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。