參數資料
型號: LAW005B8
廠商: LINEAGE POWER LLC
元件分類: 電源模塊
英文描述: 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE
封裝: MODULE-23
文件頁數: 5/8頁
文件大?。?/td> 352K
代理商: LAW005B8
Lineage Power
5
Data Sheet
LAW005-Series Power Modules; dc-dc Converters:
April 2008
36 Vdc to 75 Vdc Input; 5 W
Test Configurations
1-0304
Note: Input reflected-ripple current is measured with a simulated
source impedance of 12 H. Capacitor Cs offsets possible
battery impedance. Current is measured at the input of the
module.
Figure 1. Input Reflected-Ripple Test Setup
1-0305
Note: Use a 0.1 F ceramic capacitor. Scope measurement should
be made using a BNC socket. Position the load between
50.8 mm and 76.2 mm (2 in. and 3 in.) from the module.
Figure 2. Peak-to-Peak Output Noise
Measurement Test Setup
1-0306
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
Figure 3. Output Voltage and Efficiency
Measurement Test Setup
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL 60950, CSA C22.2 No. 60950-00, and VDE
0805 (IEC60950).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module's output to be considered
meeting the requirements of safety extra-low voltage
(SELV), all of the following must be true:
n
The input source is to be provided with reinforced
insulation from any other hazardous voltages, includ-
ing the ac mains.
n
One VI pin and one VO pin are to be grounded, or
both the input and output pins are to be kept floating.
n
The input pins of the module are not operator acces-
sible.
n
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module's output.
Note: Do not ground either of the input pins of the
module without grounding one of the output
pins. This may allow a non-SELV voltage to
appear between the output pins and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The input to these units is to be provided with a maxi-
mum 5 A normal-blow fuse in the ungrounded lead.
Feature Description
Output Overvoltage Protection (single output mod-
ules only)
Output overvoltage protection is not a feature on dual
output modules. For single output modules, the output
overvoltage protection consists of a Transient Voltage
Suppressor (TVS) diode across the output terminals.
During an ouput overvoltage fault condition, this diode
protection clamps the output within the voltages shown
in Table 5
TO OSCILLOSCOPE
CS 220 F
IMPEDANCE < 0.1
Ω
@ 20 C, 100 kHz
VI(+)
VI(-)
LTEST
BATTERY
12 H
VO (+)
VO (–)
RESISTIVE
LOAD
SCOPE
0.1 F
COPPER STRIP
VI(+)
VI(-)
VO(+)
VO(-)
II
IO
SUPPLY
CONTACT RESISTANCE
CONTACT AND
DISTRIBUTION LOSSES
LOAD
η
VO +
() –VO(–)
[]IO
VI +
() –VI(–)
[]II
-------------------------------------------------
x 100
=%
相關PDF資料
PDF描述
LB-466 LOW PASS FILTER
LB-10 LOW PASS FILTER
LB-2100 LOW PASS FILTER
LB11651 STEPPER MOTOR CONTROLLER, 4 A, PZFM14
LB11668M BRUSHLESS DC MOTOR CONTROLLER, 0.8 A, PDSO10
相關代理商/技術參數
參數描述
LAW005CL 功能描述:DC/DC轉換器 15V/-15V 0.19A 5W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
LAW005F 功能描述:DC/DC轉換器 3.3V 1A 3.3W 10-Pin RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
LAW005FZ 制造商:GE Energy (formerly Lineage Power) 功能描述:CC109110450
LAW51M-HYJZ-24 制造商:OSRAM 功能描述:LED SMD AMBER
LAW51M-HYJZ-24-R18-Z 制造商:OSRAM 功能描述: