- 您現在的位置：買賣IC網 > PDF目錄358731 > LA4906 (Sanyo Electric Co.,Ltd.) 17-W, 2-Channel BTL AF High-Efficiency Power Amplifier for Car Audio Systems PDF資料下載
參數資料
| 型號： | LA4906 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 元件分類： | 音頻放大器 |
| 英文描述： | 17-W, 2-Channel BTL AF High-Efficiency Power Amplifier for Car Audio Systems |
| 中文描述： | 17鎢，雙通道橋接自動對焦高效率數字功放汽車音響系統 |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 362K |
| 代理商： | LA4906 |
No. 5714-5/10
LA4906
Sample Printed Circuit Board
1. External component descriptions
C1 and C2
· Input capacitors. A value of 2.2 μF is recommended for these capacitors. Note that the low-frequency area
characteristics can be adjusted by changing f
L
, which is determined by the values of C1 and C2. However, due to
impulse (pop) noise considerations, the value of C1 and C2 should not exceed 3.3 μF when C4 is 22 μF.
C3
· Beep amplifier input capacitor. A value the same as that of C1 and C2 is used. If the beep function is not used, connect
the beep input to PRE-GND through C3.
C4
· Set the amplifier turn-on time. A value of 22 μF is recommended. (This will result in a turn-on time of about 0.7
second.) The on time is proportional to the value of this capacitor, and any value may be used. However, due to
impulse (pop) noise considerations, a value of 22 μF or larger should be used.
C5, C6, C7, and C8
· Oscillation prevention capacitors. Polyester film (Mylar) capacitors with good temperature characteristics must be used.
(These are used together with R1, R2, R3, and R4.) We recommend values of 0.1 μF or higher for these capacitors
since the stability will differ somewhat depending on the printed circuit board layout actually used.
C9
· Decoupling capacitor (ripple filter)
C10
· Power-supply capacitor
C11
· Oscillation prevention capacitor for the switching regulator. A value of 1500 pF is recommended.
C12
· Switching regulator output smoothing capacitor. The LA4906 adopts a self-excited switching regulator technique. The
value of this capacitor must be optimized, since it influences both the self-excitation stability and the regulator
efficiency. We recommend using a 2.2-μF 25-V OS (Organic Semiconductor) capacitor with a low series resistance
and good temperature characteristics. Note that for the same reason a 2.2-
1/2-W resistor should be used for the
associated resistor R6.
R5
· Standby switch current limiter resistor. A value of 10 k
is recommended. (When the voltage applied to the standby
switch is in the range 3 to 13.2 V.) Note that this resistor cannot be removed from this circuit.
相關PDF資料 |
PDF描述 |
|---|---|
| LA50-S | Current Transducer LA 50-S/SP1 |
| LA5002 | 2V 60mA Low Saturation Voltage Regulator(輸出電壓2V，輸出電流為60mA低飽和電源穩壓器) |
| LA5008M | 8V 60mA Low Saturation Voltage Regulator(輸出電壓8V，輸出電流為60mA低飽和電源穩壓器) |
| LA5112N | COMPACT DC MOTOR SPEED CONTROLLER |
| LA5112N | LA5112N |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4917H | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Linear IC Audio Output for TV application High-Effciency Two-Channel 7W BTL Power Amplifier ICs |
| LA4919N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Linear IC Two-Channel 10W BTL High-Efficiency TV Audio Output Power Amplifier |
| LA4B-M1C2LV-G | 制造商:IDEC CORPORATION 功能描述:Switch Push Button N.O./N.C. DPDT Flush Rectangular Button 0.1A 250VAC 250VDC Momentary Contact PC Pins Panel Mount/Through Hole |
| LA4B-M1C2LV-W | 制造商:IDEC CORPORATION 功能描述:Switch Push Button N.O./N.C. DPDT Flush Rectangular Button 0.1A 250VAC 250VDC Momentary Contact PC Pins Panel Mount/Through Hole |
| LA4CA00 | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。