- 您現在的位置：買賣IC網 > PDF目錄358731 > LA4663 (Sanyo Electric Co.,Ltd.) Two-Channel 16-W BTL General-Purpose Audio Power Amplifier(雙16W BTL 通用音頻功率放大器) PDF資料下載
參數資料
| 型號： | LA4663 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Two-Channel 16-W BTL General-Purpose Audio Power Amplifier(雙16W BTL 通用音頻功率放大器) |
| 中文描述： | 雙通道16鎢橋接通用音頻功率放大器（雙16周橋接通用音頻功率放大器） |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 113K |
| 代理商： | LA4663 |
Usage Notes
1. Maximum ratings
If the device is operated in the vicinity of the maximum ratings, it is possible for small changes in the operating
conditions to result in the maximum ratings being exceeded. Since this can result in destruction of the device,
applications should be designed with adequate margins in the supply voltage and other parameters so that the maximum
ratings are never exceeded during device operation.
2. Protection circuits
While the LA4663 includes a full complement of built-in protection circuits, care is required in the usage. In particular,
be careful not to short any pairs of device pins together.
[Notes on the shorting (power, ground, and load shorting) protection circuit]
This protection circuit operates whenever a power short (a short between the output and V
CC
), a ground short (a short
between the output and ground), or a load short (shorting between the + and – outputs) is detected. Although there are
cases where the protection circuit may not operate if the supply voltage is under 9 V, the thermal protection circuit will
protect the device in this range.
The protection circuit continues to operate during the interval that the abnormal short continues, and automatically
recovers when the error state is resolved. However, under certain usage conditions, there are situations where the
protection circuit may lock and remain locked even after the problem has been resolved. In these cases, the circuit can
be reset by switching to standby mode or turning off the power temporarily.
If the output is shorted to V
CC
with the IC in the standby state and furthermore, a V
CC
of 20 V or higher applied, an
offset will be created between the + and – outputs. If a load is connected in this state, a current will flow in that load,
and the IC may be destroyed. Applications should assure that this does not occur.
In the following situations, the operation of the protection circuit may result in a sound switching phenomenon at high
output levels. This may be a problem, depending on the details of the end product circuit itself, and must be verified in
an actual system.
At low load resistances R
L
(high loads) and at high V
CC
voltages, and with both channels operating at I
O
peak levels of
over 2 A per channel. (This phenomenon is more likely to occur the higher the chip temperature.)
For systems operating under the most sever conditions (high temperatures and high outputs), specific operating
conditions such that the above phenomenon does no occur are listed in the “Allowable operating supply voltage range
(V
CC
op)” item in the Operating Conditions section of the specifications. (Refer to the V
CC
op ranges for different R
L
values.)
[Thermal protection circuit]
A thermal protection circuit is provided to prevent damage to or destruction of the IC itself when the IC generates
abnormally high temperatures. This means that gradual attenuation is applied to the output signals by the thermal
protection circuit if the IC junction temperature (Tj) rises above about 160°C due to insufficient heat sinking or other
problems.
3. Notes on printed circuit boards
When designing the printed circuit board pattern, keep the input lines separated from both the VCC lines and the
output lines. This is to prevent increased distortion and oscillation.
When high output levels are used, make power-ground lines as wide as possible and as short as possible to prevent the
PWR GND pins potential from increasing with respect to pre-ground. (From the standpoint of IC stability, ideally, the
ground pin potential should be the lowest potential in the system. This is to prevent trouble caused by several types of
induced parasitic devices due to increases in the GND pin potential due to the structure of the IC.)
No. 5905-3/10
LA4663
相關PDF資料 |
PDF描述 |
|---|---|
| LA4700N | 2-Channel 12W AF Power Amplifier for Car Stereos(用于汽車立體聲的輸出功率12W雙 AF功率放大器) |
| LA4700 | 2-Channel 12W AF Power Amplifier for Car Stereos |
| LA4705 | 15 W 2-channel BTL AF Power Amplifier for Car Stereos |
| LA4708 | 20 W 2-channel BTL AF Power Amplifier for Car Stereos(用于汽車立體聲的輸出功率20W雙BTL AF功率放大器) |
| LA4725 | 2-Channel BTL Power Amplifier (30W+30W) with Standby Switch for Car Stereos(用于汽車立體聲雙BTL功率放大器（30W+30W，帶備用開關）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4663-B-E | 制造商:ON Semiconductor 功能描述:AUDIO AMPLIFIER BTL 2CH - Ammo Pack |
| LA4663-E | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LA46B-DBKUG-7-PF | 制造商:LIGITEK 制造商全稱:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA46B-EG-4-PF | 制造商:LIGITEK 制造商全稱:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA46B-EG-9-PF | 制造商:LIGITEK 制造商全稱:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
發布緊急采購，3分鐘左右您將得到回復。