- 您現在的位置：買賣IC網 > PDF目錄358729 > LA4422 (Sanyo Electric Co.,Ltd.) 5.8W typ AF Power Amplifier for Car Stereos, Car Radios PDF資料下載
參數資料
| 型號： | LA4422 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 元件分類： | 音頻放大器 |
| 英文描述： | 5.8W typ AF Power Amplifier for Car Stereos, Car Radios |
| 中文描述： | 5.8W典型自動對焦功率放大器汽車音響，車載收音機 |
| 文件頁數： | 3/10頁 |
| 文件大小： | 429K |
| 代理商： | LA4422 |
LA4422
No.556–3/10
Functions of External Parts
The recommended number of external parts of the LA4422 is 4 pcs. as follows.
· Feedback capacitor from pin (5) C
NF
.
· Pin (7) to (10) bootstrap capacitor C
BS
.
· Output capacitor from pin (10) C
OUT
.
· High frequency parasitic oscillation compensating capacitor C
X
.
The fixed values of these parts are C
NF
=100
μ
F, C
BS
=100
μ
F, C
OUT
=1000
μ
F, C
X
=0.15
μ
F. We now consider what will occur
when these values are changed.
(a) Feedback capacitor C
NF
If C
NF
is made smaller, the combined series impedance with R
NF
at a low frequency is increased, the amplification
degree A
vf
is decreased, and the low cutoff frequency is made higher as seen from the following equation.
Rf
1
j
C
NF
Avf=
VG=20log Avf (dB)
The ripple rejection is also lowered. It is possible, however, to make the starting time earlier at the time of the power
supply switch ON. If C
NF
is made larger, these are reversed.
(b) Bootstrap capacitor C
BS
The low cutoff frequency may be somewhat influenced, but the drive at a low frequency is more influenced. If C
BS
is
made smaller, power at a low frequency may be reduced. Therefore, C
BS
should be more than 47
μ
F.
(c) Output capacitor C
OUT
The low cutoff frequency may be somewhat influenced, but the most influence is that power is reduced as the imped-
ance at a low frequency is increased. Therefore, C
OUT
should be determined by the power band width. 470
μ
F min. is
required.
(d) High frequency parasitic oscillation compensating capacitor C
X
.
C
X
should be a polyester film capacitor of good frequency characteristic. If a ceramic capacitor is used, oscillation may
occur.
Features of IC System and Functions of Remaining Pins
· Since the input circuit uses pnp and the input potential is designed to be 0 bias, no input coupling capacitor is needed and
the direct coupling is available.
· The thermal shutdouwn protection circuit is built in to prevent breakdown or degradation attributable to generation of heat
at the time of load short or overload.
· The overvoltage protection circuit is built in to protect the IC from breaking down when a surge is applied to the power
supply line.
· The prevention circuit is provided to prevent pop noise which occures when the power supply is turned ON.
· The voltage gain of open loop is lowered and the nagative feedback is made smaller to obtain a soft clip. Radiation to the
high frequency circuit and stability are considered.
· The feedback resistor R
f
is set up at such a large value as 40k
and the cutoff frequency point f
L
is considered so that the
frequency characteristic is fully externded to a low frequency even if the capacity of capacitor C
NF
is small.
· The high frequency parasitic oscillation compensating capacitor is built in as a means to reduce the number of external
parts. Therefore, the high cutoff frequency point f
H
is fixed.
· The feedback resistor R
NF
is built in and the voltage gain is fixed to be 53dB in order to reduce the number of external
parts and to minimize the variations of voltage gain.
Pins (5) and (6) are provided to control the voltage gain externally. The voltage gain is lowered by inserting a resistor in
series with pin (5). The voltage gain is increased by inserting a resistor between pin (5) and (6). If CR are connected to
pin (6), the voltage gain is freely controlled through pin (6) alone.
· Pin (4) is provided as a decoupling pin.
Even if the power suppy is turned ON/OFF in succession, pop noise is minimized by connecting a capacitor to this pin,
provided that a condition C
D
≥
C
NF
is recommended. C
NF
is related to the starting time. The ripple rejection is improved
by connecting the decoupling capacitor C
D
.
(R
NF
+ )
相關PDF資料 |
PDF描述 |
|---|---|
| LA4425A | 5 W Power Amplifier with Very Few External Parts for Car Radio and Car Stereo |
| LA4440 | 6W 2-Channel, Bridge 19W typ Power Amplifier |
| LA4445 | 5.5W 2-Channel AF Power Amplifier |
| LA4446 | 5.5W 2-Channel AF Power Amp |
| LA4450 | Two Channel Power IC for Bus or Track Use in TV and Home Audio Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4425 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LA4425A | 制造商:Distributed By MCM 功能描述:SUB ONLY SANYO I.C.5-PIN SIP-HS 制造商:Panasonic Industrial Company 功能描述:IC |
| LA4425A_07 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Car Radio and Car Stereo 5W Power Amplifier with Very Few External Parts |
| LA4425A_10 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Car Radio and Car Stereo 5W Power Amplifier with Very Few External Parts |
| LA4425A-E | 功能描述:功率放大器 5W 1CH AB POWER AMP RoHS:否 制造商:TriQuint Semiconductor 封裝 / 箱體: 工作電源電壓:28 V 電源電流:2.5 A 工作溫度范圍: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。