- 您現在的位置：買賣IC網 > PDF目錄367494 > L9312 Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications PDF資料下載
參數資料
| 型號： | L9312 |
| 英文描述： | Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| 中文描述： | 線路接口和線路接入電路轉發電池SLIC和振鈴繼電器的訓練班- 57應用 |
| 文件頁數： | 11/40頁 |
| 文件大?。?/td> | 709K |
| 代理商： | L9312 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Data Sheet
July 2001
Forward Battery SLIC and Ringing Relay for TR-57 Applications
L9312 Line Interface and Line Access Circuit
Agere Systems Inc.
11
State Definitions
Primary Control Modes
Powerup, Forward Battery
I
Normal talk and battery feed state.
I
Pin PT is positive with respect to pin PR.
I
All ac transmission and dc feed circuits are powered
up.
I
On-hook transmission is enabled.
I
Thermal shutdown is active.
I
Battery window comparator sense shutdown is on.
I
Switch break switches (SW1 and SW2) are closed,
and ring access switches (SW3 and SW4) are open.
I
V
BAT1
is applied to tip and ring during on-hook condi-
tions.
I
Automatic battery switch selects V
BAT1
or V
BAT2
dur-
ing off-hook conditions.
I
All supervision circuits except for ring trip detector
are active.
I
NSTAT represents the loop closure detector status.
Scan
I
Scan clamp circuitry is active.
I
Loop closure is active.
I
All ac transmission, dc feed, and other supervision
circuits, including ring trip, are shut down.
I
Thermal shutdown is active.
I
Battery window comparator sense shutdown is on.
I
On-hook transmission is disabled.
I
Pin PT is positive with respect to PR, and V
BAT1
is
applied to tip/ring.
I
Switch break switches (SW1 and SW2) are closed,
and ring access switches (SW3 and SW4) are open.
I
NSTAT represents the loop closure detector status.
Ringing
I
Switch break switches (SW1 and SW2) are open,
and ring access switches (SW3 and SW4) are
closed.
I
Tip/ring drive amplifiers are powered down.
I
Ring trip circuit is active.
I
Loop supervision and common-mode current detec-
tors are powered down.
I
NSTAT represents the ring trip detector status.
Disconnect
—
Break Before Make
I
The tip and ring amplifiers are turned off to conserve
power.
I
Break switches (SW1 and SW2) are open, and ring
access switches (SW3 and SW4) are open. This
mode is also used as a transitional mode to achieve
break-before-make switching from the power ring to
active or scan mode.
I
All supervision circuits are powered down; NSTAT
overrides the actual loop condition and is forced high
(on-hook).
Reset
I
Selection of device reset via the RESET pin will set
the device into the disconnect break-before-make
state.
Special States
Thermal Shutdown
I
Not controlled via truth table inputs.
I
This mode is caused by excessive heating of the
device, such as may be encountered in an extended
power cross situation.
I
Upon reaching the thermal shutdown temperature,
the device will enter an all-off mode.
I
Upon cooling, the device will re-enter the state it was
in prior to thermal shutdown.
I
Hysteresis is built in to prevent oscillation. In this
mode, supervision output NSTAT is forced low
(off-hook) regardless of loop status or if the discon-
nect logic state is selected.
相關PDF資料 |
PDF描述 |
|---|---|
| L9313 | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| L9350 | Single Peripheral Driver |
| L9355 | Dual Peripheral Driver |
| L9500A | High-Voltage Ringing SLIC for VolP Applications |
| L9653M | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9313 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| L9324 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Peripheral Driver |
| L9326 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L-932P3C | 制造商:Kingbright Corporation 功能描述: |
| L-9331 | 制造商:Ideal Industries Inc 功能描述:L-9331 |
發布緊急采購，3分鐘左右您將得到回復。