- 您現在的位置：買賣IC網 > PDF目錄367494 > L9216A CAP CER 270PF 3.15KVDC R3 RAD PDF資料下載
參數資料
| 型號： | L9216A |
| 英文描述： | CAP CER 270PF 3.15KVDC R3 RAD |
| 中文描述： | 短環振鈴用戶接口與地面開始 |
| 文件頁數： | 32/48頁 |
| 文件大?。?/td> | 1062K |
| 代理商： | L9216A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Preliminary Data Sheet
September 2001
Short-Loop Ringing SLIC with Ground Start
L9216A/G
32
Agere Systems Inc.
ac Applications
ac Parameters
There are four key ac design parameters.
Termination
impedance
is the impedance looking into the 2-wire
port of the line card. It is set to match the impedance of
the telephone loop in order to minimize echo return to
the telephone set.
Transmit gain
is measured from the
2-wire port to the PCM highway, while
receive gain
is
done from the PCM highway to the transmit port.
Transmit and receive gains may be specified in terms
of an actual gain, or in terms of a transmission level
point (TLP), that is the actual ac transmission level
in dBm. Finally, the
hybrid balance
network cancels
the unwanted amount of the receive signal that
appears at the transmit port.
Codec Types
At this point in the design, the codec needs to be
selected. The interface network between the SLIC and
codec can then be designed. Below is a brief codec
feature summary.
First-Generation Codecs
These perform the basic filtering, A/D (transmit), D/A
(receive), and
μ
-law/A-law companding. They all have
an op amp in front of the A/D converter for transmit
gain setting and hybrid balance (cancellation at the
summing node). Depending on the type, some have
differential analog input stages, differential analog out-
put stages, 5 V only or
±
5 V operation, and
μ
-law/A-law
selectability. These are available in single and quad
designs. This type of codec requires continuous time
analog filtering via external resistor/capacitor networks
to set the ac design parameters. An example of this
type of codec is the Agere T7504 quad 5 V only codec.
This type of codec tends to be the most economical in
terms of piece part price, but tends to require more
external components than a third-generation codec.
Further ac parameters are fixed by the external R/C
network so software control of ac parameters is diffi-
cult.
Third-Generation Codecs
This class of devices includes all ac parameters set
digitally under microprocessor control. Depending on
the device, it may or may not have data control latches.
Additional functionality sometimes offered includes
tone plant generation and reception, PPM generation,
test algorithms, and echo cancellation. Again, this type
of codec may be 3.3 V, 5 V only, or
±
5 V operation, sin-
gle quad or multichannel, and
μ
-law/A-law or 16-bit lin-
ear coding selectable. Examples of this type of codec
are the Agere T8535/6 (5 V only, quad, standard fea-
tures), T8537/8 (3.3 V only, quad, standard features),
T8533/4 (5 V only, quad with echo cancellation), and
the T8531/32 (5 V only multichannel).
ac Interface Network
The ac interface network between the L9216 and the
codec will vary depending on the codec selected. With
a first-generation codec, the interface between the
L9216 and codec actually sets the ac parameters. With
a third-generation codec, all ac parameters are set dig-
itally, internal to the codec; thus, the interface between
the L9216 and this type of codec is designed to avoid
overload at the codec input in the transmit direction
and to optimize signal to noise ratio (S/N) in the receive
direction.
Because the design requirements are very different
with a first- or third-generation codec, the L9216 is
offered with two different receive gains. Each receive
gain was chosen to optimize, in terms of external com-
ponents required, the ac interface between the L9216
and codec.
相關PDF資料 |
PDF描述 |
|---|---|
| L9217A | CAP CER 2700PF 3.15KVDC R3 RAD |
| L9218A | CAP CER 330PF 3.15KVDC R3 RAD |
| L9219A | CAP CER 390PF 3.15KVDC R3 RAD |
| L9310 | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
| L9311 | Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9217A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| L9218A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| L9219A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| L9222 | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9222_04 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD INVERTING TRANSISTOR SWITCH |
發布緊急采購，3分鐘左右您將得到回復。