- 您現在的位置：買賣IC網 > PDF目錄383238 > L6926Q1TR (意法半導體) High efficiency monolithic synchronous step down regulator PDF資料下載
參數資料
| 型號： | L6926Q1TR |
| 廠商： | 意法半導體 |
| 英文描述： | High efficiency monolithic synchronous step down regulator |
| 中文描述： | 高效率單片同步降壓穩壓器 |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 178K |
| 代理商： | L6926Q1TR |
Operation description
L6926
10/17
4.3
Slope compensation
In current mode architectures, when the duty cycle of the application is higher than
approximately 50%, a pulse-by-pulse instability (the so called sub harmonic oscillation) can
occur.
To allow loop stability also in these conditions a slope compensation is present. This is
realized by reducing the current flowing through the inductor necessary to trigger the COMP
comparator (with a fixed value for the COMP pin voltage).
With a given duty cycle higher than 50%, the stability problem is particularly present with an
higher input voltage (due to the increased current ripple across the inductor), so the slope
compensation effect increases as the input voltage increases.
From an application point of view, the final effect is that the peak current limit depends both
on the duty cycle (if higher than approximately 40%) and on the input voltage.
4.4
Loop stability
Since the device is realized with a current mode architecture, the loop stability is usually not
a big issue. For most of the application a 220pF connected between the COMP pin and
ground is enough to guarantee the stability. In case very low ESR capacitors are used for
the output filter, such as multilayer ceramic capacitors, the zero introduced by the capacitor
itself can shift at very high frequency and the transient loop response could be affected.
Adding a series resistor to the 220pF capacitor can solve this problem.
The right value for the resistor (in the range of 50K) can be determined by checking the load
transient response of the device. Basically, the output voltage has to be checked at the
scope after the load steps required by the application. In case of stability problems, the
output voltage could oscillates before to reach the regulated value after a load step.
相關PDF資料 |
PDF描述 |
|---|---|
| L6926 | HIGH EFFICIENCY MONOLITHIC SYNCHRONOUS STEP DOWN REGULATOR |
| L6926D013TR | HIGH EFFICIENCY MONOLITHIC SYNCHRONOUS STEP DOWN REGULATOR |
| L6926D | HIGH EFFICIENCY MONOLITHIC SYNCHRONOUS STEP DOWN REGULATOR |
| L6928D | HIGH EFFICIENCY MONOLITHIC SYNCHRONOUS STEP DOWN REGULATOR |
| L6928D013TR | HIGH EFFICIENCY MONOLITHIC SYNCHRONOUS STEP DOWN REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6928 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High efficiency monolithic synchronous step down regulator |
| L6928_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High efficiency monolithic synchronous step down regulator |
| L6928_11 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High efficiency monolithic synchronous step down regulator |
| L6928D | 功能描述:直流/直流開關調節器 Hi Efficiency Mono Step-Down Reg RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| L6928D013TR | 功能描述:直流/直流開關調節器 2.0 to 5.5V Step-Dwn RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。