- 您現在的位置：買賣IC網 > PDF目錄383238 > L6911DTR (意法半導體) 5 BIT PROGRAMMABLE STEP DOWN CONTROLLER WITH SYNCHRONOUS RECTIFICATION PDF資料下載
參數資料
| 型號： | L6911DTR |
| 廠商： | 意法半導體 |
| 英文描述： | 5 BIT PROGRAMMABLE STEP DOWN CONTROLLER WITH SYNCHRONOUS RECTIFICATION |
| 中文描述： | 5位可編程降壓控制器采用同步整流 |
| 文件頁數： | 3/17頁 |
| 文件大小： | 233K |
| 代理商： | L6911DTR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
3/17
L6911D
PIN FUNCTION
Pin
Num.
Name
Description
1
VSEN
Connected to the output voltage is able to manage over-voltage conditions and the PGOOD
signal.
2
OCSET
A resistor connected from this pin and the upper Mos Drain sets the current limit protection.
The internal 200
μ
A current generator sinks a current from the drain through the external resistor.
The Over-Current threshold is due to the following equation:
I
R
DSon
3
SS/INH
The soft start time is programmed connecting an external capacitor from this pin and GND. The
internal current generator forces through the capacitor 10
μ
A.
This pin can be used to disable the device forcing a voltage lower than 0.4V
4 - 8
VID0 - 4
Voltage Identification Code pins. These input are internally pulled-up and TTL compatible. They
are used to program the output voltage as specified in Table 1 and to set the overvoltage and
power good thresholds.
Connect to GND to program a ‘0’ while leave floating to program a ‘1’.
9
COMP
This pin is connected to the error amplifier output and is used to compensate the voltage control
feedback loop.
10
FB
This pin is connected to the error amplifier inverting input and is used to compensate the voltage
control feedback loop.
11
GND
All the internal references are referred to this pin. Connect it to the PCB signal ground.
12
PGOOD
This pin is an open collector output and is pulled low if the output voltage is not within the above
specified thresholds.
If not used may be left floating.
13
PHASE
This pin is connected to the source of the upper mosfet and provides the return path for the high
side driver. This pin monitors the drop across the upper mosfet for the current limit
14
UGATE
High side gate driver output.
15
BOOT
Bootstrap capacitor pin. Through this pin is supplied the high side driver and the upper mosfet.
Connect through a capacitor to the PHASE pin and through a diode to Vcc (cathode vs. boot).
16
PGND
Power ground pin. This pin has to be connected closely to the low side mosfet source in order to
reduce the noise injection into the device
17
LGATE
This pin is the lower mosfet gate driver output
18
VCC
Device supply voltage. The operative nominal supply voltage ranges from 5 to 12V.
DO NOT CONNECT V
IN
TO A VOLTAGE GREATER THAN V
CC
.
19
OVP
Over voltage protection. If the output voltage reaches the 17% above the programmed voltage
this pin is driven high and can be used to drive an external SCR that crowbar the supply voltage.
If not used, it may be left floating.
20
RT
Oscillator switching frequency pin. Connecting an external resistor from this pin to GND, the
external frequency is increased according to the equation:
Connecting a resistor from this pin to Vcc (12V), the switching frequency is reduced according to
the equation:
If the pin is not connected, the switching frequency is 200KHz.
The voltage at this pin is fixed at 1.23V (typ). Forcing a 50
μ
A current into this pin, the built in
oscillator stops to switch.
I
P
---------------------------------------------
=
f
S
200kHz
6
T
)
-------------------------
+
=
f
S
200kHz
7
T
----------------------------
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| L6918 | 5 BIT PROGRAMMABLE MULTIPHASE CONTROLLER |
| L6918A | 5 BIT PROGRAMMABLE MULTIPHASE CONTROLLER |
| L6918AD | 5 BIT PROGRAMMABLE MULTIPHASE CONTROLLER |
| L6918ADTR | 5 BIT PROGRAMMABLE MULTIPHASE CONTROLLER |
| L6918D | 5 BIT PROGRAMMABLE MULTIPHASE CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6911E | 功能描述:DC/DC 開關控制器 5-Bit Prog Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| L6911E_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5-Bit programmable step down controller with synchronous rectification |
| L6911ETR | 功能描述:DC/DC 開關控制器 5B PROGRAMMABLE STEP DOWN CONTROLLER RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| L6912-2 | 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,2/BG |
| L6913-1 | 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,1/BG |
發布緊急采購，3分鐘左右您將得到回復。