參數資料
型號： L6728HTR
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10
封裝： 3 X 3 MM, ROHS COMPLIANT, DFN-10
文件頁數： 28/32頁
文件大?。?/td> 1213K
代理商： L6728HTR
Obsolete
Product(s)
- Obsolete
Product(s)
L6728H
Pin description and connection diagrams
Doc ID 15725 Rev 1
5/32
2
Pin description and connection diagrams
2.1
Pin descriptions
Figure 3.
Pin connection (top view)
L6728H
Table 2.
Pins description
Pin n°
Name
Function
1BOOT
HS driver supply. Connect through a capacitor (100 nF) to the floating node (LS-Drain) pin
and provide necessary bootstrap diode from VCC.
2
PHASE
HS driver return path, current-reading and adaptive-dead-time monitor. Connect to the LS
drain to sense
RDS(on) drop to measure the output current. This pin is also used by the
adaptive-dead-time control circuitry to monitor when HS MOSFET is OFF.
3
UGATE
HS driver output. Connect directly to HS MOSFET gate.
4
LGATE / OC
LGATE. LS driver output. Connect directly to LS MOSFET gate. OC. Over current threshold
set. During a short period of time following VCC rising over UVLO threshold, a 10
μA current
is sourced from this pin. Connect to GND with an ROCSET resistor greater than 5 kΩ to
program OC threshold. The resulting voltage at this pin is sampled and held internally as the
OC set point. Maximum programmable OC threshold is 0.55 V. A voltage greater than 0.6 V
activates an internal clamp and causes OC threshold to be set at the maximum value.
5GND
All internal references, logic and drivers are connected to this pin. Connect to the PCB ground
plane.
6VCC
Device and drivers power supply. Operative range from 5 V to 12 V. Filter with at least 1 nF
MLCC to GND.
7
COMP / DIS
COMP. Error amplifier output. Connect with an RF - CF // CP to FB to compensate the device
control loop. DIS. The device can be disabled by pushing this pin lower than 0.75 V (typ).
Setting free the pin, the device enables again.
8FB
Error amplifier inverting input. Connect with a resistor RFB to the output regulated voltage.
Output resistor divider may be used to regulate voltages higher than the reference.
9
VSEN
Regulated voltage sense pin for OVP and UVP protections and PGOOD. Connect to the
output regulated voltage, or to the output resistor divider if the regulated voltage is higher than
the reference.
10
PGOOD
Open drain output set free after SS has finished and pulled low when VSEN is outside the
relative window. Pull up to a voltage equal or lower than VCC. If not used it can be left
floating.
相關PDF資料
PDF描述
L6728H SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10
L6728 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10
L6728TR 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10
L6731BTR 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
L6731B 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
相關代理商/技術參數
參數描述
L6728TR 功能描述:DC/DC 開關控制器 Sngl phase PWM controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6730 功能描述:DC/DC 開關控制器 Adjustable Step Down Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6730_09 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Adjustable step-down controller with synchronous rectification
L6730B 功能描述:DC/DC 開關控制器 Adjustable Step Down Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6730BTR 功能描述:DC/DC 開關控制器 Adjustable Step Down Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*