- 您現在的位置：買賣IC網 > PDF目錄67754 > L6728 (STMICROELECTRONICS) 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10 PDF資料下載
參數資料
| 型號： | L6728 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10 |
| 封裝： | 3 X 3 MM, LEAD FREE, DFN-10 |
| 文件頁數： | 11/31頁 |
| 文件大?。?/td> | 1361K |
| 代理商： | L6728 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Obsolete
Product(s)
- Obsolete
Product(s)
L6728
Application information
11
Application information
11.1
Inductor design
The inductance value is defined by a compromise between the dynamic response time, the
efficiency, the cost and the size. The inductor has to be calculated to maintain the ripple
current (
ΔI
L) between 20 % and 30 % of the maximum output current (typ). The inductance
value can be calculated with the following relationship:
Where FSW is the switching frequency, VIN is the input voltage and VOUT is the output
voltage. Figure 9 shows the ripple current vs. the output voltage for different values of the
inductor, with VIN = 5 V and VIN = 12 V.
Increasing the value of the inductance reduces the current ripple but, at the same time,
increases the converter response time to a dynamic load change. The response time is the
time required by the inductor to change its current from initial to final value. Until the inductor
has not finished its charging time, the output current is supplied by the output capacitors.
Minimizing the response time can minimize the output capacitance required. If the
compensation network is well designed, during a load variation the device is able to set a
duty cycle value very different (0 % or 80 %) from steady state one. When this condition is
reached, the response time is limited by the time required to change the inductor current.
Figure 9.
Inductor current ripple vs output voltage
L
V
IN
V
OUT
–
F
SW
ΔI
L
------------------------------
V
OUT
V
IN
--------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| L6728TR | 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10 |
| L6731BTR | 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6731B | 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6731D | 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| L9230-DIE1 | STEPPER MOTOR CONTROLLER, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6728_0706 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Single phase PWM controller with Power Good |
| L6728A | 功能描述:電壓模式 PWM 控制器 Hi-Freq. singl-phase PWM controller w/Po RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| L6728AH | 功能描述:軟開關 PWM 控制器 Sgl Output 600 KHz DFPN-10 RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| L6728AHTR | 功能描述:電流型 PWM 控制器 HIGH FREQ PWM CNTRL W/PO RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| L6728ATR | 功能描述:電壓模式 PWM 控制器 HIGH FREQ SINGLE PHASE PWM CNTRL RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。