- 您現在的位置：買賣IC網 > PDF目錄383237 > L6615 (意法半導體) HIGH/LOW SIDE LOAD SHARE CONTROLLER PDF資料下載
參數資料
| 型號： | L6615 |
| 廠商： | 意法半導體 |
| 英文描述： | HIGH/LOW SIDE LOAD SHARE CONTROLLER |
| 中文描述： | 高/低側負載共享控制器 |
| 文件頁數： | 12/20頁 |
| 文件大小： | 392K |
| 代理商： | L6615 |
L6615
12/20
Figure 12. ADJ network
To set the R
ADJ
value it is necessary to know the tolerance required of the power supply output voltage
(V
OUT
±
V
O
); the maximum difference between master and slave output voltage is 2*
V
O
and this amount
represents the voltage that the L6615 must be able to correct.
Now two different approaches are feasible depending on whether the SMPS (whose output current must
be shared) has to be completely designed or it is an "off the shelf" component and only the current sharing
section must be designed.
In the first case, the adjustment resistor (R
ADJ
) can be considered as a fraction of the high resistor of the
feedback divider R
H
(see fig.12.a): typically the first step consist of fixing the current flowing, under steady
state condition, through the feedback divider I
FB
; by choosing the value for R
2
:
we will have:
It can be an useful rule of thumb to use R
ADJ
lower than (or equal to) one tenth of R1, considering that, in
worst case condition, it will be:
This value must not exceed the one indicated in the "Electrical characteristic section" but this is very easy
to meet, as one can easily see by using sensible values for
V
OUT
and R
2
.
In the second case (fig 12.b), the feedback divider has been already designed by the SMPS manufacturer
and it is not possible to modify it: the design of R
ADJ
must be done to make the L6615 able to correct the
maximum spread without significantly shifting the SMPS regulation point. A minimum R
ADJ
value can be
found by:
where I
ADJ(max)
is 8mA.
Especially for low voltage output buses it is important to avoid adjustment network saturation; the design
must satisfy the following relationship:
where V
ADJ(MIN)
can be found in the "Electrical characteristic section" for different I
ADJ
values.
V
OUT
V
REF
POWER SUPPLY
R
ADJ
E/A
ADJ pin
I
ADJ
V
OUT
V
REF
R
ADJ
E/A
ADJ pin
I
ADJ
R
1
R
2
a)
b)
Off the shelf
to L6615
to L6615
I
FB
V
R
2
--------------
=
R
H
R
1
R
ADJ
+
V
V
REF
--------------
1
–
R
2
=
=
I
ADJ max
)
V
R
ADJ
------------------
=
R
ADJ min
)
V
I
ADJ max
)
-------------------------
=
V
OUT
R
ADJ
I
ADJ
I
FB
+
(
)
V
ADJ MIN
)
>
–
相關PDF資料 |
PDF描述 |
|---|---|
| L6615D | HIGH/LOW SIDE LOAD SHARE CONTROLLER |
| L6615DTR | HIGH/LOW SIDE LOAD SHARE CONTROLLER |
| L6615N | HIGH/LOW SIDE LOAD SHARE CONTROLLER |
| L6660 | MILLI-ACTUATOR DRIVER |
| L6668 | SMART PRIMARY CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6615D | 功能描述:DC/DC 開關控制器 H/L Load Share Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| L6615D013TR | 功能描述:DC/DC 開關控制器 H/L Load Share Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| L6615DTR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:HIGH/LOW SIDE LOAD SHARE CONTROLLER |
| L6615N | 功能描述:DC/DC 開關控制器 H/L Load Share Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| L6622-01 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:130 KV MICROFOCUS X-RAY SOURCE |
發布緊急采購，3分鐘左右您將得到回復。