- 您現在的位置：買賣IC網 > PDF目錄383237 > L6610 (意法半導體) DIGITALLY PROGRAMMABLE SECONDARY HOUSEKEEPING CONTROLLER PDF資料下載
參數資料
| 型號： | L6610 |
| 廠商： | 意法半導體 |
| 英文描述： | DIGITALLY PROGRAMMABLE SECONDARY HOUSEKEEPING CONTROLLER |
| 中文描述： | 數字可編程控制器二次內務管理 |
| 文件頁數： | 18/29頁 |
| 文件大小： | 544K |
| 代理商： | L6610 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
L6610
18/29
2
Three error amplifiers are implemented on the IC to achieve regulation of the output voltages: a brief description
follows for each section.
–
Main section:
error amplifier A and Soft-Start.
The circuit is designed to directly control the Main primary PWM through an optocoupler, providing
very good regulation and galvanic isolation from the primary side. Typical solutions require a shunt
regulator, like the TL431, as a reference and feedback amplifier to sense the output voltage and gen-
erate a corresponding error voltage; this voltage is then converted in a current transferred to the pri-
mary side through the optocoupler.
The feedback E/A amplifier is integrated in the IC: its non-inverting input is connected to an internally gen-
erated voltage reference, whose default value is typically 2.5V. It can however be trimmed to obtain a better
precision (see "On board trimming and mode operating" section). Then, no TL431 is needed.
The E/A inverting input (Ainv, pin#5) and the E/A output (Aout, pin#6) are externally available and the
frequency compensation network (Zc) will be connected between them (see fig. 17).
The high impedance (in the hundred k
) internal divider from 12V and 5V UV/OV sense pins elimi-
nates the need for an external one in most applications, allowing a further reduction in the number of
external component.
Under closed loop condition, the two upper branches, connected to 12V and 5V pins, supply equally
the current flowing through R3 = 80.6K (equal to 2.5V/R3).
In order to avoid high current peaks in the primary circuit and output voltage overshoots at start-up,
the IC provides an on-board 8ms soft-start, a quasi-monotonic ramp from 0V to 2.5V for the A error
amplifier reference voltage,. In fact, if this reference gets the nominal value as soon as the power-up
occurs, the A E/A will go out of regulation and tend to sink much more current, thus forcing PWM to
work with the maximum duty-cycle.
–
E/A and references voltage
Being the inverting input of E/A externally available, it is possible to change the "weight" of the two
contributions or even eliminate one of them by connecting external resistors of much lower value (R
L
,
R
H1
and/or R
H2
in fig. 17) that bypass the internal ones appropriately.
For example using R
L
=2.4K, R
H1
=3.9K and R
H2
=24K, then the ratio between +5V and +12V output
weight will be equal to 6:4.
By simply making R
H1
= R
L
(for example 2.4K) with no R
H2
, only the +5V output is kept under feed-
back because the contribution of +12V branch (through the internal 600K resistor) will be negligible.
The pin #24 (12V) has to be however connected to +12V output to guarantee the OV/UV monitoring.
ERROR AMPLIFIERS AND REFERENCE VOLTAGES
Figure 17. Main feedback section
–
3.3V section, error amplifier B.
It is the error amplifier used to set the magamp core through an external circuitry (see a typical sche-
matic in figure 18).
The non-inverting input of the error amplifier is connected to a trimmable 1.25V internal voltage ref-
erence (see "On board trimming and mode operating" paragraph). The E/A inverting input is exter-
nally available (Binv, pin#2) and is connected to the output divider (R
H
and R
L
); the output pin (Bout,
V
DD
to MAIN
control
Zc
Aout
R
B
12V
5V
+2.5V
600K
168K
80.6K
8ms SS
L6610
GND
_
+
+12V output
+5V output
Ainv
R
L
R
H1
R
H2
optional, to change
feedback weight
相關PDF資料 |
PDF描述 |
|---|---|
| L6610D | DIGITALLY PROGRAMMABLE SECONDARY HOUSEKEEPING CONTROLLER |
| L6610DTR | CAP CER 2400PF 50V 5% C0G 0805 |
| L6610N | DIGITALLY PROGRAMMABLE SECONDARY HOUSEKEEPING CONTROLLER |
| L6611 | DIGITALLY PROGRAMMABLE SECONDARY HOUSEKEEPING CONTROLLER |
| L6611D | DIGITALLY PROGRAMMABLE SECONDARY HOUSEKEEPING CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6610D | 功能描述:IC CTRLR HOUSEKEEPING BCD 24SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| L6610DTR | 功能描述:IC CTRLR HOUSEKEEPING 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| L6610N | 功能描述:IC CTRLR HOUSEKEEPING BCD 24-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| L6611 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DIGITALLY PROGRAMMABLE SECONDARY HOUSEKEEPING CONTROLLER |
| L6611D | 功能描述:IC CTRLR HOUSEKEEPING BCD 20SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。