參數資料
型號： L6566B
廠商： 意法半導體
英文描述： Multi-mode controller for SMPS
中文描述： 多模式開關電源控制器
文件頁數： 29/51頁
文件大小： 401K
代理商： L6566B
L6566B
Application information
29/51
Experience shows that this value is typically lower than the real one. Once the maximum
peak primary current, I
PKpmax
, occurring at minimum input voltage Vinmin has been found,
the value of Rs can be determined from (5):
Equation 7
The converter is then tested on the bench to find the output power level Pout
lim
where
regulation is lost (because overcurrent is being tripped) both at Vin = Vin
min
and Vin =
Vin
max
.
If Pout
lim
@ Vin
max
> Pout
lim
@ Vin
min
the system is still undercompensated and k needs
increasing; if Pout
lim
@ Vin
max
< Pout
lim
@ Vin
min
the system is overcompensated and k
needs decreasing. This will go on until the difference between the two values is acceptably
low. Once found the true k
opt
in this way, it is possible that Pout
lim
turns out slightly different
from the target; to correct this, the sense resistor Rs needs adjusting and the above tuning
process will be repeated with the new Rs value. Typically a satisfactory setting is achieved in
no more than a couple of iterations.
In applications where this function is not wanted, e.g. because of a narrow input voltage
range, the VFF pin can be simply grounded, directly or through a resistor (see “
Section 5.11:
OVP block on page 35
”). The overcurrent setpoint will be then fixed at the maximum value of
1V. If a lower setpoint is desired to reduce the power dissipation on Rs, the pin can be also
biased at a fixed voltage using a divider from VREF (pin 10).
If the FF option is selected the Line Feedforward function can be still used to compensate for
the total propagation delay Td of the current sense chain (internal propagation delay td
(H-L)
plus the turn-off delay of the external MOSFET), which in standard current mode PWM
controllers is done by adding an offset on the current sense pin proportional to the input
voltage. In that case the divider ratio k, which will be much smaller as compared to that used
with the QR option selected, can be calculated with the following equation:
max
PKp
I
min
in
opt
3
V
k
1
Rs
=
Figure 17. Left: Overcurrent setpoint vs. VFF voltage; right: Line Feedforward function block
V
csx
[V]
1.2
0
0.5
1
1.5
2
2.5
3
3.5
0
0.2
0.4
0.6
0.8
1
V
VFF
[V]
V
COMP
= Upper clamp
7
9
15
Rs
Rectified Line Voltage
DRIVER
4
R
S
Q
R1
R2
COMP
VFF
CS
GD
L6566B
1.5 V
-
Hiccup
DISABLE
VOLTAGE
FEED
FORWARD
Optional for
OVP settings
OCP
-
+
PWM
-
+
Vcsx
Clock/ZCD
相關PDF資料
PDF描述
L6566BTR Multi-mode controller for SMPS
L6567 HIGH VOLTAGE DRIVER FOR CFL
L6567D HIGH VOLTAGE DRIVER FOR CFL
L6571B High Voltage Half Bridge Driver with Oscillator(帶晶振的高電壓半橋驅動器)
L6585D PFC and Ballast Control IC
相關代理商/技術參數
參數描述
L6566B_08 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Multi-mode controller for SMPS
L6566BH 功能描述:電流型 PWM 控制器 Multimode Controller SMPS 800V <3mA RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
L6566BHTR 功能描述:電流型 PWM 控制器 MULTIMODE CONTROLLER SMPS 8V 3 mA RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
L6566BTR 功能描述:電流型 PWM 控制器 MultiMode Controller for SMPS RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
L6566BTR-CUT TAPE 制造商:ST 功能描述:L6566B Series 23 V 4.6 mA SMPS Multi-Mode Controller Surface Mount - SOIC-16N
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*