- 您現在的位置：買賣IC網 > PDF目錄67754 > L6258EX (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 1.5 A, PDSO36 PDF資料下載
參數資料
| 型號： | L6258EX |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO36 |
| 封裝： | POWER, SO-36 |
| 文件頁數： | 17/31頁 |
| 文件大?。?/td> | 305K |
| 代理商： | L6258EX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
L6258E
4
Application information
A typical application circuit is shown in Figure 11.
Note:
For avoid current spikes on falling edge of DISABLE a "DC feedback" would be added to the
ERROR Amplifier. (R1-R2 on Figure 11).
4.1
Interference
Due to the fact that the circuit operates with switch mode current regulation, to reduce the
effect of the wiring inductance a good capacitor (100nF) can be placed on the board near
the package, between the power supply line (pin 13,31) and the power ground (pin
1,36,18,19) to absorb the small amount of inductive energy.
It should be noted that this capacitor is usually required in addition to an electrolytic
capacitor, that has poor performance at the high frequencies, always located near the
package, between power supply voltage (pin 13,31) and power ground (pin 1,36,18,19), just
to have a current recirculation path during the fast current decay or during the phase
change.
The range value of this capacitor is between few F and 100F, and it must be chosen
depending on application parameters like the motor inductance and load current amplitude.
A decoupling capacitor of 100nF is suggested also between the logic supply and ground.
The EA_IN1 and EA_IN2 pins carry out high impedance lines and care must be taken to
avoid coupled noise on this signals. The suggestion is to put the components connected to
this pins close to the L6258E, to surround them with ground tracks and to keep as far as
possible fast switching outputs of the device. Remember also an 1 Mohm resistor between
EA_INx and EA_OUTx to avoid output current spike during supply startup/shutdown.
A non inductive resistor is the best way to implement the sensing. Whether this is not
possible, some metal film resistor of the same value can be paralleled.
The two inputs for the sensing of the winding motor current (SENSE_A & SENSE_B) should
be connected directly on the sensing resistor Rs terminals, and the path lead between the
Rs and the two sensing inputs should be as short as possible.
Note:
Connect the DISABLE pin to a low impedance (< 300
Ω ) voltage source to reduce at
minimum the interference on the output current due to capacitive coupling of OUT1A (pin5)
and DISABLE (pin 6).
相關PDF資料 |
PDF描述 |
|---|---|
| L6470PD | STEPPER MOTOR CONTROLLER, 7 A, PDSO36 |
| L6566BTR | 0.8 A POWER FACTOR CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6706 | SWITCHING REGULATOR, QCC40 |
| L6717 | DUAL SWITCHING CONTROLLER, 575 kHz SWITCHING FREQ-MAX, QCC48 |
| L6728HTR | SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6258EX_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PWM controlled high current DMOS universal motor driver |
| L6258EXTR | 功能描述:馬達/運動/點火控制器和驅動器 Hi-Curr Univ Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L625CME | 制造商:COOPER INDUSTRIES 功能描述:LUFKIN / TAPE,POWER,1"(25MM)X25(8 |
| L625DG | 制造商:LIGHTING COMP DESIGN 功能描述: 制造商:Lighting Components & Design Inc 功能描述: |
| L625DR | 制造商:LIGHTING COMP DESIGN 功能描述: 制造商:Lighting Components & Design Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。