參數資料
型號： L6227Q
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32
封裝： 5 X 5 MM, 1 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32
文件頁數： 24/27頁
文件大?。?/td> 435K
代理商： L6227Q
Pin connection
L6227Q
6/27
Table 4.
Pin description
N°
Pin
Type
Function
1, 21
GND
Signal ground terminals.
9OUT1B
Power output Bridge B output 1.
11
RCB
RC pin
RC network pin. A parallel RC network connected between this pin and
ground sets the current controller OFF-time of the bridge B.
12
SENSEB
Power supply
Bridge B source pin. This pin must be connected to power ground through a
sensing power resistor.
13
IN1B
Logic input
Bridge B input 1
14
IN2B
Logic input
Bridge B input 2
15
VREFB
Analog input
Bridge B current controller reference voltage.
Do not leave this pin open or connect to GND.
16
ENB
Logic input (1)
Bridge B enable. LOW logic level switches OFF all power MOSFETs of bridge
B. This pin is also connected to the collector of the overcurrent and thermal
protection transistor to implement over current protection.
If not used, it has to be connected to +5 V through a resistor.
17
VBOOT
Supply
voltage
Bootstrap voltage needed for driving the upper power MOSFETs of both
bridge A and Bridge B.
19
OUT2B
Power output Bridge B output 2.
20
VSB
Power supply
Bridge B power supply voltage. It must be connected to the supply voltage
together with pin VSA.
22
VSA
Power supply
Bridge A power supply voltage. It must be connected to the supply voltage
together with pin VSB.
23
OUT2A
Power output Bridge A output 2.
24
VCP
Output
Charge pump oscillator output.
25
ENA
Logic input (1)
Bridge A enable. LOW logic level switches OFF all power MOSFETs of bridge
A. This pin is also connected to the collector of the overcurrent and thermal
protection transistor to implement over current protection.
If not used, it has to be connected to +5 V through a resistor.
26
VREFA
Analog input
Bridge A current controller reference voltage.
Do not leave this pin open or connect to GND.
27
IN1A
Logic input
Bridge A logic input 1.
28
IN2A
Logic input
Bridge A logic input 2.
29
SENSEA
Power supply
Bridge A source pin. This pin must be connected to power ground through a
sensing power resistor.
30
RCA
RC pin
RC network pin. A parallel RC network connected between this pin and
ground sets the current controller OFF-time of the bridge A.
31
OUT1A
Power output Bridge A output 1.
1.
Also connected at the output drain of the over current and thermal protection MOSFET. Therefore, it has to be driven
putting in series a resistor with a value in the range of 2.2 k
- 180 k, recommended 100 k.
相關PDF資料
PDF描述
L6228D STEPPER MOTOR CONTROLLER, 2.8 A, PDSO24
L6228N STEPPER MOTOR CONTROLLER, 2.8 A, PDIP24
L6229QTR BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, QCC32
L6229Q BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, QCC32
L6230PDTR BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO36
相關代理商/技術參數
參數描述
L6227Q_09 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS dual full bridge driver with PWM current controller
L6227QTR 功能描述:功率驅動器IC DMOS DUAL FULL Bridge w/ PWM RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6228 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS DRIVER FOR BIPOLAR STEPPER MOTOR
L6228D 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L6228DTR 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*