- 您現在的位置：買賣IC網 > PDF目錄383234 > L5995 (意法半導體) Accurate 4 Bit Programmable Power Supply Controller for Mobile CPU(用于移動CPU的精確4位可編程電源控制器) PDF資料下載
參數資料
| 型號： | L5995 |
| 廠商： | 意法半導體 |
| 英文描述： | Accurate 4 Bit Programmable Power Supply Controller for Mobile CPU(用于移動CPU的精確4位可編程電源控制器) |
| 中文描述： | 精確的4位可編程電源控制器，用于移動CPU（用于移動處理器的精確4位可編程電源控制器） |
| 文件頁數： | 5/10頁 |
| 文件大小： | 78K |
| 代理商： | L5995 |
FUNCTIONAL PIN DESCRIPTION
ENABLE(pin1):
(>2.4V) enables the device, a low level (<0.8V)
shuts it down. As ENABLE drops below 0.8V, the
drivers are turned off and all internalfunctionsare
disabled except REG5. In this condition the stand
by currentis less than 80
μ
A at VIN = 12V.
Enable input.
A
high level
VIN(pin2):
Device supply voltage. Input voltage
range at this pin is 4.75V to 25V and the operat-
ing current requirement at 12Vis 650
μ
A.
REG5(pin3):
5V Regulator supply. Used also to
supply the bootstrap capacitor. A minimum 2.2
μ
F
ceramic capacitor connected to PWRGND is re-
quired.
V5SW(pin4):
5V supply line. Connecting to 5V
bus(4.75V to 5.5V) the device is no longer pow-
ered by VIN but by this pin and the internal linear
regulator is disconnected increasing the effi-
ciency.
CRST(pin5):
Controlstart up. An externalcapaci-
tor connected to this pin defines the delay be-
tween the output voltage Vo has reached 90% of
VPROG and POWERGOOD leading edge signal
will start to go high. This delay could be calcu-
lated
using
the
Tst(ms)=16*C(
μ
F).
follows
formula:
SSTART(pin6):
Soft Start. The soft-start time is
programmed by an external capacitor connected
between this pin and SGND. The internal current
generator forces 4
μ
A throughthe capacitorimple-
mentingthe soft startfunction.
HRSNS(pin7):
Error summing current sense non
inverting input.
LRSNS(pin8):
Error summing current sense in-
verting input.
VFB(pin9):
Regulator voltage feedback input.
Connect close to the CPU input supply pin realise
an accurate voltage regulation. VFB internally is
connected to the window comparator that is used
to increase the performanceduring the load tran-
sient.
COMP(pin10):
Regulator stability compensation
pin. The compensation is realised internally and
normally it is not necessaryto connect any exter-
nal componentsto this pin .
VPROG(pin11):
Reference voltage test pin. This
pin provides the DAC output and should be de-
coupled to ground using a 0.22
μ
F ceramic ca-
pacitor. No load has to be connected.
SNSGND(pin12):
Remote ground sense. This
pin is internally connected to the low power cir-
cuitry and for a precise output voltage regulation
can be connected to the output capacitor nega-
tiveterminal.
V
IN2.5
(pin13):
2.5V linear supply voltage. Is avail-
able on-chip a linear regulator useful for the 2.5V
bus. A max input voltage of 3.3V is recom-
mended at Iomax(150mA).
V
O2.5
(pin14):
2.5V linear regulator output.
linear regulator is realised with an internal NPN
transistor
with +/-2% output accuracy. A mini-
mum
of
47
μ
F
capacitor connected
PWRGND is required.
The
versus
VBG(pin15):
Band-gap reference voltage. A min
220nF ceramic capacitor is required to assure the
band gap stability and noise immunity.
VSS(pin16):
Signal ground. This pin could be
connectedto the PWRGND pin.
FREQ(pin17):
Connecting an external resistor
versus ground is possible to select the switching
frequency between 100kHz and 1MHz. Using an
Rext=680k the fsw is 100kHz, using an Rext =
40k the fsw is 1MHz. In this condition is recom-
mended to connect the OSC pin to REG5 or to
VSS.
OSC(pin18):
Connecting to REG5 is able to set
the switching frequency at 250kHz, connecting to
VSS is able to set the switching frequency at
300kHz. An external pulsed signal, with an ampli-
tude higher than 2.4V, could synchronise the de-
vice. In all these conditions pin FREQ has to be
connectedto REG5.
OVP(pin19):
Over voltage protection pin. If con-
nected ti GND the device works in normal opera-
tion activating OVP and UVLO output controls. If
connected to REG5 the OVP and UVLO controls
are disabled. If OVP = GND and ENABLE = GND
or the NO-CPU condition is set the high side is
maintained off and the low side is on. If OVP =
REG5 and ENABLE = GND or the NO-CPU con-
dition is set the high side and the low side are
maintainedoff.
L5995
5/10
相關PDF資料 |
PDF描述 |
|---|---|
| L5996 | 5 BIT DYNAMIC DAC CONTROLLER FOR MOBILE CPU |
| L5NK65Z | N-CHANNEL 650V - 1.5ohm - 4.2A PowerFLAT⑩ Zener-Protected SuperMESH⑩Power MOSFET |
| L6000 | SINGLE CHIP READ & WRITE CHANNEL |
| L602-L604 | DARLINGTON ARRAYS |
| L601 | DARLINGTON ARRAYS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L5996 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5 BIT DYNAMIC DAC CONTROLLER FOR MOBILE CPU |
| L-59BL/1EGW | 制造商:Kingbright Corporation 功能描述: 制造商:Kingbright Corporation 功能描述:LED 5MM RED/GREEN 40MCD/60MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/GREEN, 40MCD/60MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/GREEN, 40MCD/60MCD, LED Colour:Red, Green, Height:7.24mm, Width:7. 制造商:Kingbright Corporation 功能描述:Red/grn r/a cbi,5mm,L-59BL/1EGW |
| L-59BL/1EYW | 制造商:Kingbright Corporation 功能描述: 制造商:Kingbright Corporation 功能描述:LED 5MM RED/YELLOW 40MCD/40MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/YELLOW, 40MCD/40MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/YELLOW, 40MCD/40MCD, LED Colour:Red, Yellow, Height:7.24mm, Width: |
| L-59BL/1GEW | 制造商:Kingbright Corporation 功能描述: |
| L-59BL/1GYW | 制造商:Kingbright Corporation 功能描述:LED 5MM GREEN/YELLOW 100/40MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, GREEN/YELLOW, 100/40MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, GREEN/YELLOW, 100/40MCD, LED Colour:Yellow, Green, Height:7.24mm, Widt |
發布緊急采購，3分鐘左右您將得到回復。