參數資料
型號: L5951
廠商: 意法半導體
英文描述: TRIPLE OUTPUT MULTIFUNCTION VOLTAGE REGULATOR FOR CAR RADIO WITH IDR/CLASS 2 INTERFACE
中文描述: 三路輸出的多功能車將IDR無線電穩壓器/電壓類2接口
文件頁數: 4/13頁
文件大?。?/td> 119K
代理商: L5951
L5951
4/13
high pulse identified by a pulse width of about t = 200
μ
s.
DATA -
Total number of bytes that can be transmitted (from SOF to EOF) is 12 bytes.
Cyclic Redundancy Check (CRC) -
A method for determining if the message received is the same as the mes-
sage transmitted. If an invalid CRC number is detected, then an error will be detected. The SOF signal is not
used to determine the CRC. All bits in the CRC are initially "ones" to avoid confusion with a data stream that are
all "zeros".
End of Data (EOD) -
Used to signal the receiver about the end of data transmission. If there is a IRF signal, the
sender of the frame will expect one or more bytes in the IFR following the EOD. If there is no IFR used, then the
bus would stay in a logic level low state resulting in a EOF. EOD signal is recognized by a logic level low pulse
for a duration of about 200
μ
s.
Normalization Bit (NB) -
The sole reason for the NB is to define the start of the in-frame response. The first bit
the the IFR is passive, therefore it is necessary to have a signal that follows EOD. There are two forms to the
NB. First of all, the NB is a logic level high pulse. The two forms are distinguished by thier pulse widths. The first
form has a pulse width of about 64
μ
s and indicates if the IFR contains a CRC or not. The second form has a
longer pulse width of about 128
μ
s and also indicates if there is a CRC in the IFR or not. The manufacturer can
manipulate the NB to any of the two methods.
In-Frame Response (IFR) -
Response bytes are sent by the receiver of the transmission and start after the
EOD. If the IFR stays at a logic level low for a period of time then the frame must be considered to be complete.
IFR bytes can be used to send a signal back to the originator indicating the correct CRC number to confirm the
correct message was sent.
End of Frame (EOF) -
Indicates the end of a frame. Once the last byte is transmitted, the bus will be in a logic
level low state for a period of time indicating the end of the frame. EOF signal is recognized by a low pulse for
a width of about 280
μ
s.
Inter-Frame Separation (IFS) -
IFS is used to synchronize the receivers at various nodes.
ABSOLUTE MAXIMUM RATINGS
* denotes active low
THERMAL DATA
(*) With 6cm2 on board heat sink area.
Symbol
Parameter
Value
Unit
V
S
DC Operating Supply Voltage
-0.6 to 26.5
V
V
DIAG
Diagnostic output voltage
-0.6 to 5.5
V
V
IN
Input Control Voltage (EN, Sleep, 4X, Loop, TX)
-0.6 to 5.5
V
V
OUT
Output Control Voltage (Reset *)
-0.3 to 5.5
V
V
S
Peak Supply Voltage t = 50ms
34
V
T
op
Operating Temperature Range
-40 to 85
°C
T
stg
Storage Temperature Range
-40 to 150
°C
Symbol
Parameter
Value
Unit
R
th j-amb
Thermal resistance junction to ambient (*)
50
°C/W
相關PDF資料
PDF描述
L5952 MULTIPLE MULTIFUNCTION VOLTAGE REGULATOR
L5953 MULTIPLE SWITCHING VOLTAGE REGULATOR
L5970AD RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
L5970ADTR RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
L5970D013 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
相關代理商/技術參數
參數描述
L595100 制造商:Crouzet 功能描述:Current Transformer 1:1000 600VAC 100000mA
L5952 功能描述:線性穩壓器 - 標準 MULTI MULTIFUNCTION Vltg REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
L595200 功能描述:控制器 CUR TRANSFORMER 200A MAX RoHS:否 制造商:Omron Industrial 模擬/數字:Digital 類型:Digital Temperature Controller 顯示器類型:11-Segment, 4 Digit 電源電壓:100 VAC to 240 VAC 安裝: 控制方法: 大小:48 mm x 48 mm
L5953 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Multiple switching voltage regulator
L5953_07 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Multiple switching voltage regulator