參數資料
型號: L320ML11PI
廠商: Advanced Micro Devices, Inc.
英文描述: 32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
中文描述: 32兆位(2米× 16位/ 4米× 8位)的MirrorBit⑩3.0伏特,只有統一閃存部門與VersatileI /輸出⑩控制
文件頁數: 4/59頁
文件大?。?/td> 657K
代理商: L320ML11PI
2
Am29LV320MH/L
26517B4 January31,2007
D A T A S H E E T
GENERAL DESCRIPTION
The Am29LV320MH/L is a 32 Mbit, 3.0 volt single
power supply flash memory device organized as
2,097,152 words or 4,194,304 bytes. The device has
an 8-bit/16-bit bus and can be programmed either in
the host system or in standard EPROM programmers.
An access time of 90, 100, 110, or 120 ns is available.
Note that each access time has a specific operating
voltage range (V
CC
) and an I/O voltage range (V
IO
), as
specified in the
Product Selector Guide
and the
Order-
ing Information
sections. The device is offered in a
56-pin TSOP or 64-ball Fortified BGA package. Each
device has separate chip enable (CE#), write enable
(WE#) and output enable (OE#) controls.
Each device requires only a
single 3.0 volt power
supply
for both read and write functions. In addition to
a V
CC
input, a high-voltage
accelerated program
(ACC)
feature provides shorter programming times
through increased current on the WP#/ACC input. This
feature is intended to facilitate factory throughput dur-
ing system production, but may also be used in the
field if desired.
The device is entirely command set compatible with
the
JEDEC single-power-supply Flash standard
.
Commands are written to the device using standard
microprocessor write timing. Write cycles also inter-
nally latch addresses and data needed for the pro-
gramming and erase operations.
The
sector erase architecture
allows memory sec-
tors to be erased and reprogrammed without affecting
the data contents of other sectors. The device is fully
erased when shipped from the factory.
Device programming and erasure are initiated through
command sequences. Once a program or erase oper-
ation has begun, the host system need only poll the
DQ7 (Data# Polling) or DQ6 (toggle)
status bits
or
monitor the
Ready/Busy# (RY/BY#)
output to deter-
mine whether the operation is complete. To facilitate
programming, an
Unlock Bypass
mode reduces com-
mand sequence overhead by requiring only two write
cycles to program data instead of four.
The
VersatileI/O
(V
IO
) control allows the host sys-
tem to set the voltage levels that the device generates
and tolerates on the CE# control input and DQ I/Os to
the same voltage level that is asserted on the V
IO
pin.
Refer to the
Ordering Information
section for valid V
IO
options.
Hardware data protection
measures include a low
V
CC
detector that automatically inhibits write opera-
tions during power transitions. The hardware sector
protection feature disables both program and erase
operations in any combination of sectors of memory.
This can be achieved in-system or via programming
equipment.
The
Erase Suspend/Erase Resume
feature allows
the host system to pause an erase operation in a given
sector to read or program any other sector and then
complete the erase operation. The
Program Sus-
pend/Program Resume
feature enables the host sys-
tem to pause a program operation in a given sector to
read any other sector and then complete the program
operation.
The
hardware RESET# pin
terminates any operation
in progress and resets the device, after which it is then
ready for a new operation. The RESET# pin may be
tied to the system reset circuitry. A system reset would
thus also reset the device, enabling the host system to
read boot-up firmware from the Flash memory device.
The device reduces power consumption in the
standby mode
when it detects specific voltage levels
on CE# and RESET#, or when addresses have been
stable for a specified period of time.
The
Write Protect (WP#)
feature protects the first or
last sector by asserting a logic low on the WP#/ACC
pin. The protected sector will still be protected even
during accelerated programming.
The
Secured Silicon Sector
provides a
128-word/256-byte area for code or data that can be
permanently protected. Once this sector is protected,
no further changes within the sector can occur.
AMD MirrorBit flash technology combines years of
Flash memory manufacturing experience to produce
the highest levels of quality, reliability and cost effec-
tiveness. The device electrically erases all bits within a
sector simultaneously via hot-hole assisted erase. The
data is programmed using hot electron injection.
相關PDF資料
PDF描述
L320ML12NF 32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML12NI 32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML12PF 32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML12PI 32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML90NF 32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
相關代理商/技術參數
參數描述
L320ML12NF 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML12NI 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML12PF 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML12PI 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
L320ML90NF 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:32 Megabit (2 M x 16-Bit/4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control