- 您現在的位置：買賣IC網 > PDF目錄383230 > L292 (意法半導體) SWITCH-MODE DRIVER FOR DC MOTORS PDF資料下載
參數資料
| 型號： | L292 |
| 廠商： | 意法半導體 |
| 英文描述： | SWITCH-MODE DRIVER FOR DC MOTORS |
| 中文描述： | 開關模式直流電動機驅動 |
| 文件頁數： | 3/12頁 |
| 文件大?。?/td> | 161K |
| 代理商： | L292 |
SYSTEM DESCRIPTION
The L290, L291 and L292 are intended to be used
as a 3-chip microprocessor controlled positioning
system. The device may be used separately - par-
ticularly the L292 motor driver - but since they will
usually be used together, a description of a typical
L290/1/2 system follows.
Figure 1. System Block Diagram
The system operates in two modes to achieve high
speed, high-accurancy positioning.
Speed commands for the system originate in the
microprocessor. It is continuosly updated on the
motor position by means of pulses from the L290
tachometer chip, whitch in tur gets its information
from the optical encoder. From this basic input, the
microprocessor computes a 5-bit control word that
sets the system speed dependent on the distance
to travel.
When the motor is stopped and the microprocessor
orders it to a new positio, the system operates
initially in an open-loop configuration as there is no
feedback from the tachometer generator. A maxi-
mum speed is reached, the tachometer chip output
backs off the processor signal thus reducing accel-
ering torque. The motor continues to run at rop
speed but under closed-loop control.
As the target position is approached, the microproc-
essor lowers the value of the speed-demand word;
this reduces the voltage at the main summing point,
in effect braking the motor. The braking is applied
progressively until the motor is running at minimum
speed.
At the time, the microprocessor orders a switch to
the position mode, (strobe signal at pin 8 of L291)
and within 3 to 4 ms the L292 drives the motor to
a null position, where it is held by electronic "de-
tenting".
The mechanical/electrical interface consists of an
optical encoder which generates two sinusoidal
signals 90
°
out of phase (leading according to the
motor direction) and proportional in frequency to the
speed of rotation. The optical encoder also provides
an output at one position on the disk which is used
to set the initial position.
The opto encoder signals, FTA and FTB are filtered
by the networks R
2
C
2
and R
3
C
3
(referring to Fig.4)
and are supplied to the FTA/FTB inputs on the L290.
The main function on the L290 is to implement the
following expression:
Output signal
(
TACHO
)
=
dV
AB
dt
FTA
|
FTA
|
dV
AA
dt
FTB
|
FTB
|
Thus the mean value of TACHO is proportional to
the rotation speed and its polarity indicates the
direction of rotation.
The above function is performed by amplifying the
input signals in A
1
and A
2
to obtain V
AA
and V
AB
(typ.7 V
p
). From V
AA
and V
AB
the external differen-
tiatior RC networks R
5
C
6
and R
4
C
4
give the signals
V
MA
and V
MB
which are fed to the multipliers.
3/12
L292
相關PDF資料 |
PDF描述 |
|---|---|
| L293C | PUSH-BRIDGE DRIVER PUSH-PULL FOUR CHANNEL/DUAL |
| L293 | PUSH-PULL FOUR CHANNEL DRIVER WITH DIODES |
| L296PHT | HIGH CURRENT SWITCHINGREGULATORS |
| L296 | HIGH CURRENT SWITCHINGREGULATORS |
| L296P | HIGH CURRENT SWITCHINGREGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L292 | 制造商:STMicroelectronics 功能描述:IC SWITCH MODE DRIVER 292 |
| L292_03 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SWITCH-MODE DRIVER FOR DC MOTORS |
| L292B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L292H | 功能描述:馬達/運動/點火控制器和驅動器 DC Switch-Mode RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L293 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PUSH-PULL FOUR CHANNEL DRIVER WITH DIODES |
發布緊急采購，3分鐘左右您將得到回復。