參數資料
型號： kts6029
廠商： SIEMENS AG
英文描述： 2 Band TV Tuner(2波段的TV調諧器)
中文描述： 2波段電視調諧器（2波段的電視調諧器）
文件頁數： 11/25頁
文件大?。?/td> 453K
代理商： KTS6029
Preliminary Data Sheet
KTS6027, KTS6029
Semiconductor Group
7
2.6.99
9.3
Data is exchanged between the processor and the PLL via the I
2
C bus. The clock is generated by the proces-
sor (input SCL), while pin SDA functions as an input or output depending on the direction of the data (open
collector, external pull-up resistor). Both inputs have hysteresis and a low-pass characteristic, which enhance
the noise immunity of the I
2
C bus.
I
2
C-Bus Interface
The data from the processor pass through an I
2
C bus controller. Depending on their function the data are sub-
sequently stored in registers. If the bus is free, both lines will be in the marking state (SDA, SCL are HIGH).
Each telegram begins with the start condition and ends with the stop condition. Start condition: SDA goes
LOW, while SCL remains HIGH. Stop condition: SDA goes HIGH while SCL remains HIGH. All further infor-
mation transfer takes place during SCL = LOW, and the data is forwarded to the control logic on the positive
clock edge.
The table ”Bit Allocation” (
see 9.3.1 Bit Allocation Read / Write on page 8
) should be referred to the following
description. All telegrams are transmitted byte-by-byte, followed by a ninth clock pulse, during which the con-
trol logic returns the SDA line to LOW (acknowledge condition). The first byte is comprised of seven address
bits. These are used by the processor to select the PLL from several peripheral components (chip select). The
LSB bit (R/W) determines whether data are written into (R/W = 0) or read from (R/W = 1) the PLL.
In the data portion of the telegram during a WRITE operation, the MSB bit of the first or third data byte deter-
mines whether a divider ratio or control information is to follow. In each case the second byte of the same data
type has to follow the first byte.
If the address byte indicates a READ operation, the PLL generates an acknowledge and then shifts out the
status byte onto the SDA line. If the processor generates an acknowledge, a further status byte is output; oth-
erwise the data line is released to allow the processor to generate a stop condition. The status word consists
of two bits from the TTL input ports, three bits from the A/D converter, the lock flag and the power-on flag.
Four different chip addresses can be set by appropriate cDC level atf pin CAS (
see 9.3.4 Address selection on
page 9
).
When the supply voltage is applied, a power-on reset circuit prevents the PLL from setting the SDA line to
LOW, which would block the bus. The power-on reset flag POR is set at power-on and if V
VCC
falls below
3.2 V. It will be reset at the end of a READ operation.
相關PDF資料
PDF描述
KTS6029-2 NEUTRIK
KTY23-5 Silicon Temperature Sensors
KTY23-6 Silicon Temperature Sensors
KTY23-7 Silicon Temperature Sensors
KTY16-6 Silicon Temperature Sensors
相關代理商/技術參數
參數描述
KTS6029-2 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2 Band TV Tuner Mixer-Oscillator-PLL with unbalanced IF-Amplifier
KTS-8-1 制造商:Kings Electronics 功能描述:
KTS-8-2 制造商:Kings Electronics 功能描述:Cable Stripper 制造商:Kings Electronics 功能描述:Cable Stripper; For Use With:179DT & Various Cables ;RoHS Compliant: NA
KTSB11 功能描述:STEP DRILL BIT #11 - DOUBLE-FLUT 制造商:klein tools, inc. 系列:- 零件狀態:在售 工具類型:鉆頭，階梯式鉆頭 配套使用產品/相關產品:鉆孔 重量:0.3 磅（136.08g） 標準包裝:6
KTSB15 功能描述:STEP DRILL BIT #15 - DOUBLE-FLUT 制造商:klein tools, inc. 系列:- 零件狀態:在售 工具類型:鉆頭，階梯式鉆頭 配套使用產品/相關產品:鉆孔 重量:0.463 磅（210.01g） 標準包裝:6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*