參數資料
型號： KSZ8873MLL AM
廠商： Micrel Inc
文件頁數： 53/115頁
文件大?。?/td> 0K
描述： IC ETHERNET SWITCH 3PORT 64-LQFP
產品培訓模塊： KSZ8873 Ethernet Switches
特色產品： KSZ8873 Ethernet Switch Controller
標準包裝： 160
控制器類型： 以太網開關控制器
接口： MII
電源電壓： 1.8V，2.5V，3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-PQFP（10x10）
包裝： 托盤
其它名稱： 576-3633
KSZ8873MLL AM-ND
KSZ8873MLLAM
Micrel, Inc.
KSZ8873MLL/FLL/RLL
September 20, 2013
42
Revision 1.6
For KSZ8873MLL/FLL/RLL I2C Master configuration, the EEPROM stores the configuration data for Register 0 to
Register 120 (as defined in the KSZ8873MLL/FLL/RLL register map) with the exception of the “Read Only” status
registers. After the de-assertion of reset, the KSZ8873MLL/FLL/RLL sequentially reads in the configuration data for all
control registers, starting from Register 0.
....
RST_N
SCL
SDA
t
prgm<15 ms
Figure 8. EEPROM Configuration Timing Diagram
The following is a sample procedure for programming the KSZ8873MLL/FLL/RLL with a pre-configured EEPROM:
1.
Connect the KSZ8873MLL/FLL/RLL to the EEPROM by joining the SCL and SDA signals of the respective devices.
2.
Enable I
2C master mode by setting the KSZ8873MLL/FLL/RLL strap-in pins, P2LED[1:0] to “00”.
3.
Check to ensure that the KSZ8873MLL/FLL/RLL reset signal input, RSTN, is properly connected to the external reset
source at the board level.
4.
Program the desired configuration data into the EEPROM.
5.
Place the EEPROM on the board and power up the board.
6.
Assert an active-low reset to the RSTN pin of the KSZ8873MLL/FLL/RLL. After reset is de-asserted, the
KSZ8873MLL/FLL/RLL begins reading the configuration data from the EEPROM. The KSZ8873MLL/FLL/RLL checks
that the first byte read from the EEPROM is “88”. If this value is correct, EEPROM configuration continues. If not,
EEPROM configuration access is denied and all other data sent from the EEPROM is ignored by the
KSZ8873MLL/FLL/RLL.
Note: For proper operation, check to ensure that the KSZ8873MLL/FLL/RLL PWRDN input signal is not asserted during
the reset operation. The PWRDN input is active low.
I
2C Slave Serial Bus Configuration
In managed mode, the KSZ8873MLL/FLL/RLL can be configured as an I2C slave device. In this mode, an I2C master
device (external controller/CPU) has complete programming access to the KSZ8873MLL/FLL/RLL’s 198 registers.
Programming access includes the Global Registers, Port Registers, Advanced Control Registers and indirect access to
the “Static MAC Table”, “VLAN Table”, “Dynamic MAC Table,” and “MIB Counters.” The tables and counters are indirectly
accessed via registers 121 to 131.
In
I
2C slave mode, the KSZ8873MLL/FLL/RLL operates like other I2C slave devices. Addressing the
KSZ8873MLL/FLL/RLL’s 8-bit registers is similar to addressing Atmel’s AT24C02 EEPROM’s memory locations. Details of
I
2C read/write operations and related timing information can be found in the AT24C02 Datasheet.
相關PDF資料
PDF描述
PIC16LF1825-E/ML MCU PIC 14KB FLASH 16QFN
PIC16F57-I/SP IC MCU FLASH 2KX12 28-DIP
PIC16F630T-I/ST IC MCU FLASH 1KX14 14TSSOP
KSZ8841-32MQL IC MAC CTRLR 32BIT 128-PQFP
PIC16F631-I/ML IC PIC MCU FLASH 1KX14 20QFN
相關代理商/技術參數
參數描述
KSZ8873MLL-EVAL 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8873MLLI 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x RMII Interface (Industrial Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MLLJ 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x RMII Interface (Extended Temp) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MML 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 2x MII Interface, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MML-EVAL 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 2x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*