- 您現在的位置：買賣IC網 > PDF目錄16860 > KSZ8041TL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8041TL PDF資料下載
參數資料
| 型號： | KSZ8041TL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 13/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION KSZ8041TL |
| 標準包裝： | 1 |
| 主要目的： | 接口，以太網 PHY |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8041TL |
| 主要屬性： | 單芯片 PHY，100BASE-TX/100BASE-FX/10BASE-T |
| 次要屬性： | MII，RMII，HP Auto MDI，MDI-X 自動極性校正，LinkMD |
| 已供物品： | 板 |
| 產品目錄頁面： | 1080 (CN2011-ZH PDF) |
| 相關產品： | 576-2971-5-ND - IC ETHERNET PHY IND 48-TQFP KSZ8041TL TR-ND - TRANSCEIVER 10/100 48-TQFP KSZ8041TLA3TR-ND - TRANSCEIVER 10/100 48-TQFP KSZ8041TLA3-ND - TRANSCEIVER 10/100 48-TQFP 576-1619-ND - TRANSCEIVER 10/100BASE 48-TQFP |
| 其它名稱： | 576-3295 KSZ8041TL-EVAL-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
Micrel, Inc.
KSZ8041TL/FTL
April 2007
20
M9999-042707-1.1
MII Management (MIIM) Interface
The KSZ8041TL/FTL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the state of the
KSZ8041TL/FTL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY
settings. Further detail on the MIIM interface can be found in Clause 22.2.4.5 of the IEEE 802.3u Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows an external controller
to communicate with one or more KSZ8041TL/FTL devices. Each KSZ8041TL/FTL device is assigned a PHY
address between 1 and 7 by the PHYAD[2:0] strapping pins.
An internal addressable set of thirteen 16-bit MDIO registers. Register [0:6] are required, and their functions are
defined by the IEEE 802.3u Specification. The additional registers are provided for expanded functionality.
The KSZ8041TL/FTL supports MIIM in MII mode, RMII mode and SMII mode.
The following table shows the MII Management frame format for the KSZ8041TL/FTL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 1. MII Management Frame Format
Interrupt (INTRP)
INTRP (pin 21) is an optional interrupt signal that is used to inform the external controller that there has been a status
update in the KSZ8041TL/FTL PHY register. Bits[15:8] of register 1Bh are the interrupt control bits, and are used to
enable and disable the conditions for asserting the INTRP signal. Bits[7:0] of register 1Bh are the interrupt status bits, and
are used to indicate which interrupt conditions have occurred. The interrupt status bits are cleared after reading register
1Bh.
Bit 9 of register 1Fh sets the interrupt level to active high or active low.
MII Data Interface
The Media Independent Interface (MII) is specified in Clause 22 of the IEEE 802.3u Specification. It provides a common
interface between physical layer and MAC layer devices, and has the following key characteristics:
Supports 10Mbps and 100Mbps data rates.
Uses a 25 MHz reference clock, sourced by the PHY.
Provides independent 4-bit wide (nibble) transmit and receive data paths.
Contains two distinct groups of signals: one for transmission and the other for reception.
By default, the KSZ8041TL/FTL is configured in MII mode after it is power-up or reset with the following:
A 25 MHz crystal connected to XI, XO (pins 15, 14), or an external 25MHz clock source (oscillator) connected to
XI.
CONFIG[2:0] (pins 27, 41, 40) set to ‘000’ (default setting).
相關PDF資料 |
PDF描述 |
|---|---|
| EEU-FR1J180 | CAP ALUM 18UF 63V 20% RADIAL |
| MLG0603S3N6S | INDUCTOR MULTILAYER 3.6NH 0201 |
| KSZ8051MLL-EVAL | BOARD EVALUATION FOR KSZ8051MLL |
| MLG0603S2N7S | INDUCTOR MULTILAYER 2.7NH 0201 |
| EV-ADF4002SD1Z | BOARD EVAL FOR ADF4002 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8041TLI | 功能描述:以太網 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041TLI TR | 功能描述:以太網 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041TLI-S | 功能描述:以太網 IC Physical Layer Transceiver 10/100BASE-FX (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041TL-S | 功能描述:以太網 IC Physical Layer Transceiver 10/100BASE-T/TX (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051MLL | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (48-LQFP) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。