參數資料
型號： IV83C154DXXX-30
廠商： TEMIC SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP44
文件頁數： 20/81頁
文件大?。?/td> 663K
代理商： IV83C154DXXX-30
27
ATtiny28L/V
1062F–AVR–07/06
Port B
Port B is an 8-bit input port.
One I/O address location is allocated for the Port B Input Pins – PINB, $16. The Port B
Input Pins address is read-only.
All port pins have pull-ups that can be switched on for all Port B pins simultaneously. If
any of the Port B special functions is enabled, the corresponding pull-up(s) is disabled.
When pins PB0 to PB7 are externally pulled low, they will source current (I
IL) if the inter-
nal pull-up resistors are activated.
The Port B pins with alternate functions are shown in Table 11.
Port B as General Digital Input All eight pins in Port B have equal functionality when used as digital input pins.
PBn, general input pin: To switch the pull-up resistors on, the PLUPB bit in the MCUCS
register must be set (one). This bit controls the pull-up on all Port B pins. To turn the
pull-ups off, this bit has to be cleared (zero). Note that if any Port B pins are used for
alternate functions, the pull-up on the corresponding pins are disabled. The port pins are
tri-stated when a reset condition becomes active, even if the clock is not running.
Alternate Functions of Port B
All Port B pins are connected to a low-level detector that can trigger the low-level input
interrupt. See “Low-level Input Interrupt” on page 21 for details. In addition, Port B has
the following alternate functions:
INT1 – Port B, Bit 4
INT1, External Interrupt source 1. The PB4 pin can serve as an external interrupt source
to the MCU. See the interrupt description for details on how to enable and configure this
interrupt. If the interrupt is enabled, the pull-up resistor on PB4 is disabled and PB4 will
not give low-level interrupts.
INT0 – Port B, Bit 3
INT0, External Interrupt source 0. The PB3 pin can serve as an external interrupt source
to the MCU. See the interrupt description for details on how to enable and configure this
interrupt. If the interrupt is enabled, the pull-up resistor on PB3 is disabled and PB3 will
not give low-level interrupts.
T0 – Port B, Bit 2
T0, Timer/Counter0 Counter source. See the timer description for further details. If T0 is
used as the counter source, the pull-up resistor on PB2 is disabled and PB2 will not give
low-level interrupts.
Table 11. Port B Pin Alternate Functions
Port Pin
Alternate Functions
PB0
AIN0 (Analog Comparator Positive Input)
PB1
AIN1 (Analog Comparator Negative Input)
PB2
T0 (Timer/Counter 0 External Counter Input)
PB3
INT0 (External Interrupt 0 Input)
PB4
INT1 (External Interrupt 1 Input)
相關PDF資料
PDF描述
IT80C52XXX-16SHXXX 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
IR80C52XXX-12:R 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
MR83C154TXXX-20P883D 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44
MQ80C52TXXX-20:D 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQFP44
MR80C32-20/883:RD 8-BIT, 20 MHz, MICROCONTROLLER, CQCC44
相關代理商/技術參數
參數描述
IV83C154-L16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
IV83C154T-12 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
IV83C154T-16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
IV83C154T-20 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
IV83C154T-25 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*