參數資料
型號： ISP1181A
廠商： NXP Semiconductors N.V.
英文描述： Full-speed Universal Serial Bus peripheral controller
中文描述： 全速通用串行總線外設控制器
文件頁數： 22/70頁
文件大?。?/td> 341K
代理商： ISP1181A
Philips Semiconductors
ISP1181A
Full-speed USB peripheral controller
Product data
Rev. 05 — 08 December 2004
22 of 70
9397 750 13959
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
11.2 Resume conditions
A wake-up from the suspend state is initiated either by the USB host or by the
application:
USB host
: drives a K-state on the USB bus (global resume)
Application
: remote wake-up through a HIGH level on input WAKEUP or a LOW
level on input CS (if enabled using bit WKUPCS in the Hardware Configuration
register). Wake-up on CS will work only if V
BUS
is present.
The steps of a wake-up sequence are as follows:
1. The internal oscillator and the PLL multiplier are re-enabled. When stabilized, the
clock signals are routed to all internal circuits of the ISP1181A.
2. The SUSPEND output is deasserted, and bit RESUME in the Interrupt register is
set. This will generate an interrupt if bit IERESUME in the Interrupt Enable
register is set.
3. Maximum 15 ms after starting the wake-up sequence, the ISP1181A resumes its
normal functionality.
4. In case of a remote wake-up, the ISP1181A drives a K-state on the USB bus for
10 ms.
5. Following the deassertion of output SUSPEND, the application restores itself and
other system components to the normal operating mode.
6. After wake-up, the internal registers of the ISP1181A are write-protected to
prevent corruption by inadvertent writing during power-up of external
components. The firmware must send an Unlock Device command to the
ISP1181A to restore its full functionality.
11.3 Control bits in suspend and resume
Fig 7.
SUSPEND and WAKEUP signals in a powered-off modem application.
WAKEUP
8031
RST
RING DETECTION
ISP1181A
DP
DM
USB
VBUS
VBUS
VCC
LINE
004aaa673
SUSPEND
Table 12:
Register
Interrupt
Summary of control bits
Bit
SUSPND
BUSTATUS
Function
a transition from awake to the suspend state was detected
monitors USB bus status (logic 1 = suspend); used when
interrupt is serviced
a transition from suspend to the resume state was detected
RESUME
相關PDF資料
PDF描述
ISP1181ADGG Full-speed Universal Serial Bus peripheral controller
ISP1181B Full-speed Universal Serial Bus peripheral controller
ISP1181BBS Full-speed Universal Serial Bus peripheral controller
ISP1181BDGG Full-speed Universal Serial Bus peripheral controller
ISP1181 Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件)
相關代理商/技術參數
參數描述
ISP1181ABS 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller
ISP1181ABS,518 功能描述:USB 接口集成電路 USB 1.1 ADV DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181ABS,551 功能描述:USB 接口集成電路 USB 1.1 ADVANCED DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181ABS,557 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181ABSGE 功能描述:IC USB CNTRLR FULL-SPD 48-HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*