- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1103 (NXP Semiconductors N.V.) Universal Serial Bus transceiver PDF資料下載
參數資料
| 型號： | ISP1103 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Serial Bus transceiver |
| 中文描述： | 通用串行總線收發器 |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 484K |
| 代理商： | ISP1103 |
Philips Semiconductors
ISP1103
USB transceiver
Preliminary specification
Rev. 01 — 4 October 1999
3 of 17
9397 750 06329
Philips Electronics N.V. 1999. All rights reserved.
5.
Pinning information
5.1 Pinning
5.2 Pin description
Fig 2.
Pinning diagram SO14.
Fig 3.
Pinning diagram SSOP14.
Fig 4.
Pinning diagram TSSOP14.
fpage
MBL091
ISP1103D
1
2
3
4
5
6
7
8
14
13
12
11
10
9
MODE
RCV
VP
VM
SUSPND
GND
n.c.
SPEED
D
D
+
VPO/VO
VMO/FSE0
VCC(3.3)
OE
fpage
MBL092
ISP1103DB
1
2
3
4
5
6
7
8
14
13
12
11
10
9
MODE
RCV
VP
VM
SUSPND
GND
n.c.
SPEED
D
D
+
VPO/VO
VMO/FSE0
VCC(3.3)
OE
fpage
MBL093
ISP1103DH
1
2
3
4
5
6
7
8
14
13
12
11
10
9
MODE
RCV
VP
VM
SUSPND
GND
n.c.
SPEED
D
D
+
VPO/VO
VMO/FSE0
VCC(3.3)
OE
Table 2:
Symbol
MODE
Pin description
Pin
1
Type
I
Description
driver interface selection input (Schmitt trigger):
LOW:
Philips Encoded Data Interface (pins VO, FSE0)
HIGH:
USB-IF Standard Data Interface (pins VPO, VMO);
pulled HIGH by an internal pull-up transistor, if left floating
output enable input (Schmitt trigger, active LOW); enables the
transceiver to transmit data on the bus
differential data receiver output (CMOS level); driven HIGH
when input SUSPND is HIGH; the output state of RCV is
preserved and stable during an SE0 condition
single-ended D
+
receiver output (CMOS level); used for
external detection of single-ended zero (SE0), error
conditions, speed of connected device
single-ended D
receiver output (CMOS level); used for
external detection of single-ended zero (SE0), error
conditions, speed of connected device
suspend input (Schmitt trigger); a HIGH level enables
low-power state while the USB bus is inactive and drives
output RCV to a HIGH level
ground supply
not connected
speed selection input (Schmitt trigger); adjusts the slew rate
of differential data outputs D
+
and D
according to the
transmission speed:
OE
2
I
RCV
3
O
VP
4
O
VM
5
O
SUSPND
6
I
GND
n.c.
SPEED
7
8
9
-
-
I
LOW:
low-speed (1.5 Mbit/s)
HIGH:
full-speed (12 Mbit/s)
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1104 | Advanced Universal Serial Bus transceiver |
| ISP1104W | Advanced Universal Serial Bus transceiver |
| ISP1105 | Advanced Universal Serial Bus transceivers |
| ISP1105W | Advanced Universal Serial Bus transceivers |
| ISP1106 | Advanced Universal Serial Bus transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1103D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver |
| ISP1103DB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver |
| ISP1103DH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver |
| ISP1104 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced Universal Serial Bus transceiver |
| ISP1104W | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced Universal Serial Bus transceiver |
發布緊急采購，3分鐘左右您將得到回復。