- 您現在的位置：買賣IC網 > PDF目錄353459 > ISO120 Precision Low Cost ISOLATION AMPLIFIER PDF資料下載
參數資料
| 型號： | ISO120 |
| 元件分類： | 隔離放大器 |
| 英文描述： | Precision Low Cost ISOLATION AMPLIFIER |
| 中文描述： | 精密低成本隔離放大器 |
| 文件頁數： | 14/16頁 |
| 文件大小： | 184K |
| 代理商： | ISO120 |
7
ISO120/121
f
3dB ≈
1. 2
200 k
150 pF + C
2
()
FIGURE 1. Block Diagram.
C
1, C2 ISO120/121
EXTERNAL CLOCK
MODULATOR, DEMODULATOR
FREQUENCY RANGE
EXTERNAL CAPACITOR
400kHz to 700kHz
none
200kHz to 400kHz
500pF
100kHz to 200kHz
1000pF
50kHz to 100kHz
2200pF
20kHz to 50kHz
4700pF
10kHz to 20kHz
0.01
F
5kHz to 10kHz
0.022
F
The value of the external modulator capacitor, C
1, depends on
the frequency of the external clock signal. Table I lists
recommended values.
Synchronizing to a 400kHz to 700kHz
Square-Wave External Clock
At frequencies above 400kHz, an internal clamp and filter
provides signal conditioning so that a square-wave signal can
be used to directly drive the ISO120/121. A square-wave
external clock signal can be used to directly drive the ISO120/
121 ext osc pin if: the signal is in the 400kHz to 700kHz
frequency range with a 25% to 75% duty cycle, and
±3V to
±20V level. Details of the internal clamp and filter circuitry
are shown in Figure 1.
Synchronizing to a 10% to 90%
Duty-cycle External Clock
With the addition of the signal conditioning circuit shown in
Figure 2, any 10% to 90% duty-cycle square-wave signal can
be used to drive the ISO120/121 ext osc pin. With the values
shown, the circuit can be driven by a 4Vp-p TTL signal. For
a higher or lower voltage input, increase or decrease the 1k
resistor, R
X, proportionally. e.g. for a ±4V square wave
(8Vp-p) R
X should be increased to 2k.
The value of C
X used in the Figure 2 circuit depends on the
frequency of the external clock signal. Table II shows recom-
mended capacitor values.
Note: For external clock frequencies below 400kHz, external
modulator/demodulator capacitors are required on the
ISO120/121 as before.
TABLE I. Recommended ISO120/121 External Modulator/
Demodulator Capacitor Values vs External Clock
Frequency.
The value of the external demodulator capacitor, C
2, depends
on the value of the external modulator capacitor. To assure
stability, C
2 must be greater than 0.8 C1. A larger value for
C
2 will decrease bandwidth and improve stability:
Where:
f
–3dB ≈ –3dB bandwidth of ISO amp with external C2 (Hz)
C
2 = External demodulator capacitor (f)
For example, with C
2 = 0.01F, the f–3dB bandwidth of the
ISO120/121 is approximately 600Hz.
1pF
S/H
G = 1
S/H
G = 6
Sense
V
OUT
Signal
Com 2
Gnd 2 –V
S2
+V
S2
Gnd 1 –V
S1
+V
S1
Signal
Com 1
V
IN
C
1H
C
1L
C
1
(1)
200k
150pF
A1
100A
Sense
200A
X
100A
Sense
200A
200k
150pF
C
2L
C
2H
C
2
(1)
X
A2
Isolation Barrier
NOTE: (1) Optional. See text.
30k
16k
Ext
Osc
16k
50pF
相關PDF資料 |
PDF描述 |
|---|---|
| ISO120BG | Precision Low Cost ISOLATION AMPLIFIER |
| ICS85411AMT | Low Skew, 1-TO-2 DIFFERENTIAL-TO-LVDS FANOUT BUFFER |
| ICS95V857 | 16-Bit Registered Transceivers With 3-State Outputs 56-SSOP -40 to 85 |
| I74F777N-B | 1-Bit Bus Transceiver |
| I74F786DB | 80x86 Bus Arbiter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISO120/ISO121 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISO120. ISO121 - Precision Low Cost ISOLATION AMPLIFIER |
| ISO-120-ACE | 制造商:ATC DIVERSIFIED ELECTRONICS 功能描述:Relay; ISO Seri; Multiple Channel; SPST; Cur-Rtg 10A; Ctrl-V 120 VAC; Socket Mou |
| ISO-120-AFA | 制造商:ATC DIVERSIFIED ELECTRONICS 功能描述:Relay; ISO Seri; Single Channel; SPST; Cur-Rtg 10A; Ctrl-V 120 VAC; Socket Mount |
| ISO-120-AFN | 制造商:ATC DIVERSIFIED ELECTRONICS 功能描述:Relay; ISO Seri; Single Channel; SPST; Cur-Rtg 10A; Ctrl-V 120 VAC; Sureface Mou |
| ISO120BG | 功能描述:隔離放大器 Prec Lo Cost Iso Amp RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比（最小值）:95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。