- 您現在的位置：買賣IC網 > PDF目錄1929 > ISL95811WFRTZ (Intersil)IC POT 256TAPS 5BYTES 8-TDFN PDF資料下載
參數資料
| 型號： | ISL95811WFRTZ |
| 廠商： | Intersil |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT 256TAPS 5BYTES 8-TDFN |
| 標準包裝： | 100 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±45 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN（3x3） |
| 包裝： | 管件 |
12
FN6759.1
October 6, 2008
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL95811 responds with an ACK. At this time, if the Data
Byte is to be written only to volatile registers, then the device
enters its standby state. If the Data Byte is to be written also
to non-volatile memory, the ISL95811 begins its internal write
cycle to non-volatile memory. During the internal non-volatile
write cycle, the device ignores transitions at the SDA and
SCL pins, and the SDA output is at a high impedance state.
When the internal non-volatile write cycle is completed, the
ISL95811 enters its standby state (see Figure 19).
The byte at address 08h determines if the Data Byte is to be
written to volatile and/or non-volatile memory (see “Memory
Data Protection
The WP pin has to be at logic HIGH to perform any Write
operation to the device. When the WP is active (LOW), the
device ignores Data Bytes of a Write Operation and does not
respond to the Data Bytes with an ACK; rather it goes into
standby state waiting for a new START condition.
A STOP condition also acts as a protection of non-volatile
memory. A valid Identification Byte, Address Byte, and total
number of SCL pulses act as a protection of both volatile
and non-volatile registers. During a Write sequence, the
Data Byte is loaded into an internal shift register as it is
received. If the Address Byte is 0 or 8, the Data Byte is
transferred to the Wiper Register (WR) or to the Access
Control Register respectively, at the falling edge of the SCL
pulse that loads the last bit (LSB) of the Data Byte. If the
Address Byte is 0, and the Access Control Register is all
zeros (default), then the STOP condition initiates the internal
write cycle to non-volatile memory.
Read Operation
A Read operation consists of a three byte instruction
followed by one or more Data Bytes (see Figure 20). The
master initiates the operation issuing the following
sequence: a START, the Identification byte with the R/W bit
set to “0”, an Address Byte, a second START, and a second
Identification byte with the R/W bit set to “1”. After each of
the three bytes, the ISL95811 responds with an ACK. The
ISL95811 then transmits the Data Byte and the master then
terminates the read operation (issuing a STOP condition)
following the last bit of the Data Byte.
The byte at address 08h determines if the Data Bytes being
read are from volatile or non-volatile memory (see “Memory
FIGURE 19. BYTE WRITE SEQUENCE
FIGURE 20. READ SEQUENCE
S
T
A
R
T
S
T
O
P
IDENTIFICATION
BYTE
ADDRESS
BYTE
DATA
BYTE
A
C
K
SIGNALS FROM
THE MASTER
SIGNALS FROM
THE ISL95811
A
C
K
0
11
A
C
K
WRITE
SIGNAL AT SDA
00 0 0
0
00
SIGNALS
FROM THE
MASTER
SIGNALS FROM
THE SLAVE
SIGNAL AT SDA
S
T
A
R
T
IDENTIFICATION
BYTE WITH
R/W = 0
ADDRESS
BYTE
A
C
K
A
C
K
00
0
11
S
T
O
P
A
C
K
0
1
0
11
IDENTIFICATION
BYTE WITH
R/W = 1
A
C
K
S
T
A
R
T
LAST READ
DATA BYTE
FIRST READ
DATA BYTE
A
C
K
000
0
00 0
000
ISL95811
相關PDF資料 |
PDF描述 |
|---|---|
| ISL96017UIRT8Z | IC POT DGTL 50K OHM 8-TDFN |
| ISPLSI 1016-110LJ | IC PLD ISP 32I/O 10NS 44PLCC |
| ISPLSI 1016E-125LJN | IC PLD ISP 32I/O 125MHZ 44PLCC |
| ISPLSI 1016EA-200LJ44 | IC PLD ISP 32I/O 200MHZ 44PLCC |
| ISPLSI 1024-90LJ | IC PLD ISP 48I/O 12NS 68PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL95811WFRTZ-TK | 功能描述:IC POT 256TAPS 5BYTES 8-TDFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95811WFUZ | 功能描述:IC POT 256TAPS 5BYTES 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95811WFUZ-T | 功能描述:IC POT 256TAPS 5BYTES 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95811WFUZ-TK | 功能描述:IC POT 256TAPS 5BYTES 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95812HRZ | 制造商:Intersil Corporation 功能描述:MULTI-PHASE VR12.5 SVD CORE CONTROLLER, 32LD 4X4 QFN - Rail/Tube 制造商:Intersil Corporation 功能描述:IC VOLT REG 1-3PHASES 32QFN |
發布緊急采購，3分鐘左右您將得到回復。