參數資料
型號: ISL9206_07
廠商: Intersil Corporation
英文描述: FlexiHash+ For Battery Authentication
中文描述: FlexiHash對于電池認證
文件頁數: 13/17頁
文件大小: 341K
代理商: ISL9206_07
13
FN9260.2
January 5, 2007
ADDRESS 0-00: DEFAULT CONFIGURATION (DCFG)
This address location stores the default configuration when
the ISL9206 is manufactured. Table 11 describes each bit in
detail. The legend for the TYPE column is given in Table 13.
ADDRESS 0-01: DEFAULT TRIM SETTING (DTRM)
This address location is writable only when the device is in
test mode. During normal operation, any data written to it will
be ignored. Table 12 describes the DTRM address in detail.
ADDRESS 0-02/03/04/05: AUTHENTICATION SECRET
SET #1 (SE1A/B/C/D)
These address locations store the first set of secrets to be
used for hash calculation. Reading and writing to this
register can be disabled by setting the SLO[1] bit at OTP
ROM location 0-00[1].
TABLE 9. CONTROL AND STATUS REGISTERS (BANK 1)
ADDRESS
NAME
DESCRIPTION
BIT 7
BIT 6
BIT 5
BIT 4
BIT3
BIT 2
BIT 1
BIT 0
1-00
MSCR
Master Control
eEEW
eINT
--
--
--
--
ASLP
SRST
1-01
STAT
Device Status
sEEW
sBER
sACC
--
DAB[1:0]
SLO[1:0]
TABLE 10. AUTHENTICATION REGISTERS (BANK 2)
ADDRESS
NAME
DESCRIPTION
BIT 7
BIT 6
BIT 5
BIT 4
BIT3
BIT 2
BIT 1
BIT 0
2-00
SESL
Secrets Selection
--
--
--
--
CSL[1:0]
SSL[1:0]
2-01
CHLG
Challenge Code Register
CHLG[31:0]
2-05
AUTH
Authentication Code Register
AUTH[7:0]
TABLE 11. DEFAULT CONFIGURATION (DCFG) REGISTER SETTINGS
BIT
NAME
TYPE
DEFAULT
DESCRIPTION
7:6
DAB[1:0]
RW
00
Device Address Bit Setting:
00 : device responds only when CS field in instruction frame is’0’
01 : device responds to any CS field value in instruction frame
10 : device responds to any CS field value in instruction frame
11 : device responds only when CS field in instruction frame is ‘1’
5:4
SPD[1:0]
RW
01
XSD Bus Speed Setting: Configures the bit rate of the XSD bus interface.
00 : 0.5x (2.89kbps)
01 : 1x (5.78kbps)
10 : 2x (11.56kbps)
11 : 4x (23.12kbps)
3
eINT
RW
1
Power-on default setting of eINT bit in the MSCR register.
2
ASLP
RW
1
Power-on default setting of ASLP bit in the MSCR register.
1:0
SLO[1:0]
RW
00
Secrets Lock-out Bits:
Bit 1 : Read/Write lock-out bit for address locations 0-02 to 0-09 (Secret Set #1 & #2)
Bit 0 : Read/Write lock-out bit for address locations 0-0A to 0-0D (Secret Set #3)
NOTE: Once Bit 0 or Bit 1 is set, writing to the OTP ROM will permanently be disabled
(after a reset cycle).
TABLE 12. DEFAULT TRIMMING (DTRM) REGISTER SETTINGS
BIT
NAME
TYPE
DEFAULT
DESCRIPTION
7
HSF
R
0
Unused
6:4
TIBB[2:0]
R
--
Reference Current Trim Setting
3:0
TOSC[3:0]
R
--
Oscillator Frequency Trim Setting
TABLE 13. LEGEND FOR THE TYPE COLUMN
TYPE
READ ACTION
WRITE ACTION
R
Read-only
Data read
Data ignored
W
Write-only
Zeros read
Data written
RW Read/Write
Data read
Data written
RC Clear after read
Data read, then
cleared
Data ignored
WC Clear after write
Zeros read
Data written, then
cleard
<>
Default setting loaded from designated OTP ROM bit
locations
W
Writing disabled after lock-out
ISL9206
相關PDF資料
PDF描述
ISL9206DRZ-T FlexiHash+ For Battery Authentication
ISL9206EVAL1 FlexiHash For Battery Authentication
ISL9208IRZ Multi-Cell Li-ion Battery Pack OCP/Analog Front End
ISL9209B Charging System Safety Circuit
ISL9209BIRZ Charging System Safety Circuit
相關代理商/技術參數
參數描述
ISL9206A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:FlexiHash+ For Battery Authentication
ISL9206ADHZR5335-060 制造商:Intersil Corporation 功能描述:- Bulk
ISL9206ADHZ-T 制造商:Intersil Corporation 功能描述:MULTI-CHEM 5PIN SOT-23 - Tape and Reel
ISL9206ADRTZ-T 制造商:Intersil Corporation 功能描述:MULTI-CHEM 8TDFN EP - Tape and Reel 制造商:Intersil Corporation 功能描述:IC, BATTERY AUTHENT, 2.6V-4.8V, TDFN-8, Supply Voltage Min:2.6V, Supply Voltage
ISL9206DHZ-T 制造商:Intersil Corporation 功能描述:MULTI-CHEM 5PIN SOT-23 - Tape and Reel 制造商:Intersil 功能描述:BATRY AUTHENTICATION DEVICE SOT 23 制造商:Intersil Corporation 功能描述:FlexiHash+ For Battery Authentication