- 您現在的位置：買賣IC網 > PDF目錄383175 > ISL9001AIRBZ-T (INTERSIL CORP) LDO with Low ISUPPLY, High PSRR PDF資料下載
參數資料
| 型號： | ISL9001AIRBZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | LDO with Low ISUPPLY, High PSRR |
| 中文描述： | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO8 |
| 封裝： | 2 X 3 MM, ROHS COMPLIANT, PLASTIC, DFN-8 |
| 文件頁數： | 9/10頁 |
| 文件大?。?/td> | 255K |
| 代理商： | ISL9001AIRBZ-T |
9
FN6433.0
January 18, 2007
LDO Regulation and Programmable Output Divider
The LDO Regulator is implemented with a high-gain
operational amplifier driving a PMOS pass transistor. The
design of the ISL9001A provides a regulator that has low
quiescent current, fast transient response, and overall
stability across all operating and load current conditions.
LDO stability is guaranteed for a 1
μ
F to 10
μ
F output
capacitor that has a tolerance better than 20% and ESR less
than 200m
Ω
. The design is performance-optimized for a 1
μ
F
capacitor. Unless limited by the application, use of an output
capacitor value above 4.7
μ
F is not recommended as LDO
performance improvement is minimal.
Soft-start circuitry integrated into each LDO limits the initial
ramp-up rate to about 30
μ
s/V to minimize current surge. The
ISL9001A provides short-circuit protection by limiting the
output current to about 425mA.
The LDO uses an independently trimmed 1V reference as its
input. An internal resistor divider drops the LDO output
voltage down to 1V. This is compared to the 1V reference for
regulation. The resistor division ratio is programmed in the
factory.
Power-On Reset Generation
The ISL9001A has a Power-on Reset signal generation
circuit which indicates that output power is good. The POR
signal is generated as follows:
A POR comparator continuously monitors the output of the
LDO. The LDO enters a power-good state when the output
voltage is above 94% of the expected output voltage for a
period exceeding the LDO PGOOD entry delay time (see
below). In the power-good state, the open-drain POR output
is in a high-impedance state. An internal 100k
Ω
pull-up
resistor pulls the pin up to the LDO output voltage. An
external resistor can be added between the POR output and
the LDO output for a faster rise time, however, the POR
output should not connect through an external resistor to a
supply greater than the LDO voltage.
The power-good state is exited when the LDO output falls
below 90% of the expected output voltage for a period longer
than the PGOOD exit delay time. While power-good is false,
the ISL9001A pulls the POR pin low.
The PGOOD entry and exit delays are determined by the
value of an external capacitor connected to the CPOR pin.
For a 0.01
μ
F capacitor, the entry and exit delays are 200ms
and 25
μ
s respectively. Larger or smaller capacitor values will
yield proportionately longer or shorter delay times. The POR
exit delay should never be allowed to be less than 10
μ
s to
ensure sufficient immunity against transient induced false
POR triggering.
Overheat Detection
The bandgap outputs a proportional-to-temperature current
that is indicative of the temperature of the silicon. This
current is compared with references to determine if the
device is in danger of damage due to overheating. When the
die temperature reaches about +140°C, if the LDO is
sourcing more than 50mA, it shuts down until the die cools
sufficiently. Once the die temperature falls back below about
+110°C, the disabled LDO is re-enabled and soft-start
automatically takes place.
ISL9001A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9001AIRCZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9001AIRFZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9001AIRJZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9001AIRKZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9001AIRLZ-T | LDO with Low ISUPPLY, High PSRR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9001AIRCZ-T | 功能描述:低壓差穩壓器 - LDO W/ANNEAL SNGLDO LW I Q HI PSRR 1.8V8LDDFN RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| ISL9001AIRFZ-T | 功能描述:IC REG LDO 2.5V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:2,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，可調式 輸出電壓:1.2 V ~ 5 V 輸入電壓:2.5 V ~ 7 V 電壓 - 壓降（標準）:0.24V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?1.2A 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-261-5，TO-261AB 供應商設備封裝:SOT-223-5 包裝:帶卷 (TR) 其它名稱:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9001AIRJZ-T | 功能描述:IC REG LDO 2.8V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:2,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，可調式 輸出電壓:1.2 V ~ 5 V 輸入電壓:2.5 V ~ 7 V 電壓 - 壓降（標準）:0.24V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?1.2A 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-261-5，TO-261AB 供應商設備封裝:SOT-223-5 包裝:帶卷 (TR) 其它名稱:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9001AIRKZ-T | 功能描述:IC REG LDO 2.85V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:2,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，可調式 輸出電壓:1.2 V ~ 5 V 輸入電壓:2.5 V ~ 7 V 電壓 - 壓降（標準）:0.24V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最小）:1.2A 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-261-5，TO-261AB 供應商設備封裝:SOT-223-5 包裝:帶卷 (TR) 其它名稱:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9001AIRLZ-T | 功能描述:IC REG LDO 2.9V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:2,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，可調式 輸出電壓:1.2 V ~ 5 V 輸入電壓:2.5 V ~ 7 V 電壓 - 壓降（標準）:0.24V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最小）:1.2A 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-261-5，TO-261AB 供應商設備封裝:SOT-223-5 包裝:帶卷 (TR) 其它名稱:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
發布緊急采購，3分鐘左右您將得到回復。