參數資料
型號： ISL81387IAZ-T
廠商： Intersil
文件頁數： 23/27頁
文件大?。?/td> 0K
描述： TXRX ESD RS-485/422 2PORT 20SSOP
產品培訓模塊： Solutions for Industrial Control Applications
標準包裝： 1
類型： 收發器
驅動器/接收器數： 2/2
規程： RS232，RS422，RS485
電源電壓： 4.5 V ~ 5.5 V
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 標準包裝
產品目錄頁面： 1241 (CN2011-ZH PDF)
其它名稱： ISL81387IAZ-TDKR
5
FN6201.3
November 21, 2007
/
Pin Descriptions
PIN
MODE
FUNCTION
485/232
BOTH
Interface Mode Select input. High for RS-485 Mode and low for RS-232 Mode.
DEN
BOTH
Driver output enable. The driver outputs, Y and Z, are enabled by bringing DEN high. They are high impedance when DEN
is low.
GND
BOTH
Ground connection.
NC
BOTH
No Connection.
ON
BOTH
In RS-232 mode only, ON high enables the charge pumps. ON low, with DEN and RXEN low (and RXEN high if QFN), turns
off the charge pumps (in RS-232 mode), and in either mode places the device in low power shutdown. In both modes, when
ON is low, and DEN is high, and RXEN is high or RXEN is low, loopback is enabled.
RXEN
BOTH
Receiver output enable. Rx is enabled when RXEN is high; Rx is high impedance when RXEN is low and, if using the QFN
package, RXEN is high. When using the QFN and the active high Rx enable function, RXEN should be high or floating.
RXEN
BOTH
Active low receiver output enable. Rx is enabled when RXEN is low; Rx is high impedance when RXEN is high and RXEN
is low. (i.e., to use active low Rx enable function, tie RXEN to GND). For single signal Tx/Rx direction control, connect RXEN
to DEN. Internally pulled high. (QFN only)
VCC
BOTH
System power supply input (5V).
VL
BOTH
Logic-Level Supply. All TTL/CMOS inputs and outputs are powered by this supply. (QFN only)
A
RS-232 Receiver input with
±15kV ESD protection. A low on A forces RA high; a high on A forces RA low.
RS-485 Inverting receiver input with
±15kV ESD protection.
B
RS-232 Receiver input with
±15kV ESD protection. A low on B forces RB high; a high on B forces RB low.
RS-485 Noninverting receiver input with
±15kV ESD protection.
DY
RS-232 Driver input. A low on DY forces output Y high. Similarly, a high on DY forces output Y low.
RS-485 Driver input. A low on DY forces output Y high and output Z low. Similarly, a high on DY forces output Y low and output Z high.
DZ
RS-232 Driver input. A low on DZ forces output Z high. Similarly, a high on DZ forces output Z low.
SLEW
RS-485 Slew rate control. With the SLEW pin high, the drivers run at the maximum slew rate (20Mbps). With the SLEW pin low, the
drivers run at a reduced slew rate (460kbps). On the QFN version, works in conjunction with SPB to select one of three
RS-485 data rates. Internally pulled high in RS-485 mode.
SPB
RS-485 Speed control. Works in conjunction with the SLEW pin to select the 20Mbps, 460kbps or 115kbps RS-485 data rate.
Internally pulled high. (QFN only)
RA
RS-232 Receiver output.
RS-485 Receiver output: If B > A by at least -40mV, RA is high; If B < A by -200mV or more, RA is low; RA = High if A and B are
unconnected (floating) or shorted together (i.e., full fail-safe).
RB
RS-232 Receiver output.
RS-485 Not used. Output is high impedance, and unaffected by RXEN and RXEN.
Y
RS-232 Driver output with
±15kV ESD protection.
RS-485 Inverting driver output with
±15kV ESD protection.
Z
RS-232 Driver output with
±15kV ESD protection.
RS-485 Noninverting driver output with
±15kV ESD protection.
C1+
RS-232 External capacitor (voltage doubler) is connected to this lead. Not needed in RS-485 Mode.
C1-
RS-232 External capacitor (voltage doubler) is connected to this lead. Not needed in RS-485 Mode.
C2+
RS-232 External capacitor (voltage inverter) is connected to this lead. Not needed in RS-485 Mode.
C2-
RS-232 External capacitor (voltage inverter) is connected to this lead. Not needed in RS-485 Mode.
V+
RS-232 Internally generated positive RS-232 transmitter supply (+5.5V). C3 not needed in RS-485 Mode.
V-
RS-232 Internally generated negative RS-232 transmitter supply (-5.5V). C4 not needed in RS-485 Mode.
ISL81387, ISL41387
相關PDF資料
PDF描述
LTC2498IUHF#PBF IC ADC 24BIT 16CH 38-QFN
LT1720IMS8#TR IC COMPARATOR DUAL HS 3/5V 8MSOP
1676863-5 CAP CER 1PF 500V 5% NP0 1206
1676862-6 CAP CER 1.2PF 200V 5% NP0 1206
1676862-5 CAP CER 1PF 200V 5% NP0 1206
相關代理商/技術參數
參數描述
ISL81387IAZ-T7A 功能描述:RS-422/RS-485 接口 IC SINGLE 5V MULTIPROTOCOL TRANS RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube
ISL81387IBZ 功能描述:TXRX ESD RS-485/422 2PORT 20SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
ISL81387IBZ-T 功能描述:TXRX ESD RS-485/422 2PORT 20SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 產品目錄頁面:1402 (CN2011-ZH PDF)
ISL81483 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers
ISL81483IB 功能描述:IC TXRX RS485/422 5V LP 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*