參數資料
型號: ISL6521CBZS2698
廠商: Intersil
文件頁數: 5/13頁
文件大?。?/td> 639K
描述: IC REG QD BCK/LINEAR 16-SOIC
標準包裝: 480
拓?fù)洌?/td> 降壓(降壓)同步(1),線性(LDO)(3)
功能: 任何功能
輸出數: 4
頻率 - 開關: 300kHz
電壓/電流 - 輸出 1: 控制器
電壓/電流 - 輸出 2: 可調式,120mA
電壓/電流 - 輸出 3: 可調式,120mA
帶 LED 驅動器: 無
帶監控器: 無
帶序列發生器: 無
電源電壓: 4.5 V ~ 5.5 V
工作溫度: 0°C ~ 70°C
安裝類型: *
封裝/外殼: 16-SOIC(0.154",3.90mm 寬)
供應商設備封裝: *
包裝: 管件
5
Functional Pin Descriptions
VCC (Pin 11)
Provide a well decoupled 5V bias supply for the IC to this
pin. This pin also provides the gate bias charge for the lower
MOSFET controlled by the PWM section of the IC, as well as
the drive current for the linear regulators. The voltage at this
pin is monitored for Power-On Reset (POR) purposes.
GND (Pin 5)
Signal ground for the controller. All voltage levels are
measured with respect to this pin.
PGND (Pin 9)
This is the power ground connection. Tie the source of the
lower MOSFET of the synchronous PWM converter to this
pin.
BOOT (Pin 7)
Floating bootstrap supply pin for the upper gate drive. The
bootstrap capacitor provides the necessary charge to turn
and hold the upper MOSFET on. Connect a suitable
capacitor (0.47礔 recommended) from this pin to PHASE.
OCSET (Pin 12)
Connect a resistor from this pin to the drain of the upper
PWM MOSFET. This resistor, an internal 40礎 current
source (typical), and the upper MOSFETs on-resistance set
the converter overcurrent trip point. An overcurrent trip
cycles the soft-start function.
The voltage at this pin is monitored for power-on reset
(POR) purposes and pulling this pin below 1.25V with an
open drain/collector device will shut down the switching
controller.
PHASE (Pin 6)
Connect this pin to the source of the PWM converter upper
MOSFET. This pin is used to monitor the voltage drop across
the upper MOSFET for overcurrent protection.
UGATE (Pin 8)
Connect UGATE pin to the PWM converters upper
MOSFET gate. This pin provides the gate drive for the upper
MOSFET.
LGATE (Pin 10)
This pin provides the gate drive for the synchronous rectifier
lower MOSFET. Connect LGATE to the gate of the lower
MOSFET.
COMP and FB (Pins 4, 3)
COMP and FB are the available external pins of the PWM
converter error amplifier. The FB pin is the inverting input of the
error amplifier. Similarly, the COMP pin is the error amplifier
output. These pins are used to compensate the voltage-mode
control feedback loop of the synchronous PWM converter.
DRIVE2, 3, 4 (Pins 1, 15, 13)
Connect these pins to the point of load or to the base
terminals of external bipolar NPN transistors. These pins are
each capable of providing 120mA of load current or drive
current for the pass transistors.
FB2, 3, 4 (Pins 2, 16, 14)
Connect the output of the corresponding linear regulators to
these pins through properly sized resistor dividers. The
voltage at these pins is regulated to 0.8V. These pins are
also monitored for undervoltage events.
Quickly pulling and holding any of these pins above 1.25V
(using diode-coupled logic devices) shuts off the respective
regulators. Releasing these pins from the pull-up voltage
initiates a soft-start sequence on the respective regulator.
Description
Operation
The ISL6521 monitors and precisely controls one
synchronous PWM converter and three configurable linear
regulators from a +5V bias input. The PWM controller is
designed to regulate the core voltage of an embedded
processor or simple down conversion for high current
applications. The PWM controller drives two MOSFETs (Q1
and Q2) in a synchronous-rectified buck converter
configuration and regulates the output voltage to a level
programmed by a resistor divider. The linear controllers are
designed to regulate three additional system voltages.
Typically, these include any I/O, memory, or clock voltages
that might be required. All three linear controllers support
up to 120mA of load current without external pass devices
or higher currents with external NPN bipolar transistors.
Initialization
The ISL6521 automatically initializes upon receipt of input
power. The Power-On Reset (POR) function continually
monitors the input bias supply voltage. The POR monitors
the bias voltage at the VCC pin. The POR function initiates
soft-start operation after the bias supply voltage exceeds its
POR threshold.
Soft-Start
The POR function initiates the soft-start sequence. The
PWM error amplifier reference input is clamped to a level
proportional to the soft-start voltage. As the soft-start voltage
slews up, the PWM comparator generates PHASE pulses of
increasing width that charge the output capacitor(s).
Similarly, all linear regulators reference inputs are clamped
to a voltage proportional to the soft-start voltage. The ramp-
up of the internal soft-start function provides a controlled
output voltage rise.
Figure 1 shows the soft-start sequence for a typical
application. At T0 the +5V bias voltage starts to ramp up
crossing the 4.5V POR threshold at time T1. On the PWM
section, the oscillators triangular waveform is compared to
ISL6521
相關PDF資料
PDF描述
ISL6528CBZ-TS2698 IC REG DL BCK/LINEAR SYNC 8-SOIC
ISL6529CBZ IC REG DL BCK/LINEAR SYNC 14SOIC
ISL6534CVZ-TR5229 IC REG 3OUT BCK/LINEAR 24EPTSSOP
ISL6549CRZR5213 IC REG DL BCK/LINEAR SYNC 16-QFN
ISL9305IRTHWLNCZ-T IC REG QD BUCK/LINEAR 16TQFN
相關代理商/技術參數
參數描述
ISL6521CBZ-T 功能描述:電壓模式 PWM 控制器 4 IN 1 PWM/LINEAR CNTRLR 5V RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
ISL6521CBZ-TS2698 功能描述:IC REG QD BCK/LINEAR 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓(降壓)同步(3),線性(LDO)(2) 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
ISL6521EVAL1 功能描述:EVALUATION BOARD 1 ISL6521 RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像,彩色(RGB) 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
ISL6521EVAL1Z 功能描述:EVALUATION BOARD 1 ISL6521 RoHS:是 類別:編程器,開發系統 >> 評估板 - DC/DC 與 AC/DC(離線)SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC,步升 輸出及類型:1,非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ISL6521IBZ 功能描述:電壓模式 PWM 控制器 4 IN 1 PWM/LINEAR CNTRLR 5V RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel