- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6299A (Intersil Corporation) Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6299A |
| 廠商： | Intersil Corporation |
| 英文描述： | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| 中文描述： | 鋰聚合物電池充電器可供兩個電源 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 222K |
| 代理商： | ISL6299A |
6
FN9212.0
June 28, 2005
GND (Pin 8)
System ground.
ICDL (Pin 9)
The ICDL pin has two functions. The first function is to
program the cradle charge current during the constant-
current mode. The voltage of this pin is 1.22V during the
constant-current mode of the cradle charger. The constant-
current mode current is programmed by the following
equations:
where R
ICDL
is the resistor in
,
connected to the ICDL pin
(see the Typical Application).
It is recommended that the charge current be programmed
in the range of 350mA to 650mA.
The second function of the ICDL pin is to monitor the actual
charge current. The voltage of this pin, V
ICDL
, is proportional
to the actual charge current, I
CHG
.
The cradle charge current should be programmed equal or
higher than the USB current; otherwise, the ICDL pin voltage
will be higher than 1.22V during the constant current mode
when the USB charger is working. The charger still works
properly but the accuracy of the current monitoring voltage
degrades and saturates at approximately 2.1V.
BAT (Pin 10)
Charger output pin. Connect this pin to the battery pack or
the battery cell. A 1μF or larger value ceramic capacitor is
recommended for decoupling. The charger relies on the
battery for stability so a battery should always be connected
to the BAT pin.
Description
The ISL6299A is designed for a single-cell Li-ion or Li-
polymer battery charging circuit that accepts both a USB port
and a desktop cradle as its power source. While the charge
current from the USB input source is fixed at 380mA, the
charge current from the cradle input is programmable
between 0.1A and 1.0A by the resistor R
ICDL
. Similarly, the
end-of-charge current is fixed at typically 80mA for the USB
input and programmable for the cradle input by the resistor
R
IMIN
.
Input Auto Selection
When both input sources are present, the charger selects
only one power source to charge the battery. When the
CRDL input is higher than the POR threshold, CRDL is
selected as the power source. Otherwise the USB input is
selected. If the CRDL input voltage is below the battery
voltage but the USB input voltage is higher than the battery
voltage, then the USB input is used to charge the battery.
The control circuit always breaks both internal power
devices before switching from one power source to the other
to avoid a cross conduction of both power MOSFETs.
USB Charge Current
When the USB port is selected as the power source, the
charge current enabled by the logic input at the USBON pin.
When the USBON is driven to logic LOW, the charger is
disabled. When the USBON is driven to logic HIGH, the
charge current is fixed at a typical value of 380mA. Thus for
the USB input, the USBON pin has a similar function as the
EN pin. The following table describes the USB charge
control by both the USBON pin and EN pin:
The USBON pin is equivalent to a logic LOW when left
floating. Typically the P-channel MOSFET for the USB input
has an r
DS(ON)
of 700m
at room temperature. With a
380mA charge current, the typical head room is 260mV.
Thus, if the input voltage drops to a level that the voltage
difference between the USB pin and the BAT pin is less than
260mV, the r
DS(ON)
becomes a limiting factor of the charge
current; and the charger drops out the constant current
regulation.
Cradle Charge Current
The cradle charge current is enabled by the EN pin only, the
USBON pin has no control on the cradle charge current. The
cradle charge current is programmed with the external
resistor connected between the ICDL pin and the GND pin.
The current can be calculated with one of the equations
given in the ICDL pin description. Two equations are used
for the cradle current calculation, each corresponds to a
different range of currents. The typical r
DS(ON)
of the
P-channel MOSFET for the CRDL input is 600m
at room
temperature. When the head room between the input and
output voltages is small, the actual charge current, similar to
the USB case, could be limited by the r
DS(ON).
On the other
hand, if the head room between the input and output
voltages is large, the charge current may be limited by the
thermal foldback threshold.
I
CLD
ICDL
---------------------
0.026
0.1A
I
CLD
0.7A
<
<
–
=
I
CDL
ICDL
---------------------
0.188
0.7A
I
CDL
1.1A
<
<
–
=
TABLE 1. USB CHARGE CONTROL
EN = LOW
EN = HIGH
USBON = LOW
Disabled
Disabled
USBON = HIGH
Enabled
Disabled
ISL6299A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6299AIRZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299IRZ | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299 | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| ISL6299IRZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6308IRZ | Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6299A_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299AEVAL1 | 功能描述:EVALUATION BOARD 1 ISL6299A RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6299AIRZ | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL6299AIRZ-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6299IRZ | 功能描述:IC CHARGER BATTERY LI-ION 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。