- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6295CV-T (INTERSIL CORP) Low Voltage Fuel Gauge PDF資料下載
參數資料
| 型號： | ISL6295CV-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Low Voltage Fuel Gauge |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | PLASTIC, MO-153-AC, TSSOP-8 |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 387K |
| 代理商： | ISL6295CV-T |
7
FN9074.0
October 25, 2005
Ictrl programming in a typical application is as follows:
VOLTAGE MEASUREMENTS
An analog multiplexer and divider network is provided to
support measurement of battery pack voltages. The A/D
control registers VPctrl and GPADctrl are used to specify the
measurement to be made. In typical applications, voltage
measurement a pack level is done using the 340mV
reference and a 10-bit magnitude resolution.
The value of the LSB in a pack voltage measurement using
the 340mV reference voltage and 15 bit resolution is given
by the formula:
V
PACK
LSB = 10.2V/2
15
= 311.3μV
VPctrl programming in a typical application is as follows:
The input source fields for the VPctrl, and GPADctrl registers
must be programmed to select the pack voltage VP and the
general purpose A/D input voltage GPAD in order for these
registers to control their intended measurements.
The measurable input range for VP is from 2.8V to 7V. The
measurable input range for GPAD is from 0V to 6.2V.
TEMPERATURE MEASUREMENTS
A/D input channels are provided for temperature
measurement using either the internal temperature sensor
or an external thermistor.
Defined within the ITctrl register is settings for the reference
utilized and the resolution desired for measurement of
temperature using the internal temperature sensor. Due to
the voltage output range of the temperature sensor, the
340mV reference must be selected.
The temperature measurement given by the internal
temperature sensor is derived using the following equation:
IT(°C) = (ITres – 22421)/78.95 °C
Typically, 10-bit resolution is selected, which results in the
following temperature measurement resolution:
IT(
) = 0.405°C/LSB
For temperature measurement using an external sensor, the
NTC pin sources a current of 12.5μA. For proper operation,
an industry standard 10k
at 25°C negative temperature
coefficient (NTC) device with a proper resistance range
should be connected between the NTC and GND pins. The
NTC reference output is only enabled during an external
temperature measurement in order to minimize power
consumption.
Defined within the ETctrl register are settings for the
reference utilized and the resolution desired for
measurement of temperature using the external temperature
sensor. The accuracy of temperature measurement using
the external thermistor is directly determined by the
characteristic of the NTC device used. It is suggested that
temperature measurements be thoroughly characterized to
extract the best-fit equation for temperature determination.
Internal to the ISL6295, a voltage inverter is provided to
translate the NTC voltage to a PTC voltage so that a larger
A/D conversion result would correspond to a higher
temperature reading. The actual voltage presented to the
ADC is as follows:
V
ADC
= V
REF
- V
NTC
where V
REF
is the reference voltage selected.
For typical NTC devices, the 340mV reference should be
used to cover the expected operational temperature range of
the battery pack. For a NTC with a 10k
resistance at 25°C,
the voltage at the NTC pin will be 125mV, which corresponds
to an ADC input of (340-125)mV = 215mV. The expected
conversion result would be 215/340 * 2
15
= 20721.
OFFSET COMPENSATION
The host software can perform offset compensation by using
an offset measurement value read from the ISL6295. When
the offset calibration is enabled within the OFFSctrl register,
the converter input is internally shorted to ground and an A/D
conversion is performed at the specified resolution. The
offset value is stored in the OFFSres register.
ACCUMULATION/TIMING
The ISL6295 incorporates four 32-bit accumulators and four
32-bit elapsed time counters. The Discharge Current
Accumulator (DCA) and the Charge Current Accumulator
(CCA) are intended to record discharge and charge capacity
values. The Discharge Time Counter (DTC) and the Charge
Time Counter (CTC) are intended to maintain the total
discharge time and charge time. Accumulated charge and
discharge values can be used to determine state of charge
of the battery as well as cycle count information. With
information provided by the elapsed time counters, average
charge and discharge currents over an extended period of
time can be calculated.
Each of the four 32-bit accumulator registers is assigned a
fixed “source” A/D result register. When the accumulator is
BIT(s)
NAME
VALUE
FUNCTION
7
EN
1
ENABLES A/D CONVERSION
6-4
Res
111
Selects 15-bit resolution
3
Ref
0
Selects 170mV Reference
2-0
Sel
000
Selects VSR as ADC input
BIT(s)
NAME
VALUE
FUNCTION
7
En
1
Enables A/D conversion
6-4
Res
010
Selects 10-bit resolution
3
Ref
1
Selects 340mV Reference
2-0
Sel
011
Selects Vpack (VP) as ADC input
ISL6295
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6295 | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
| ISL6295CV | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
| ISL6299AIRZ | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299A | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| ISL6299AIRZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6295CVZ | 功能描述:IC FUEL GAUGE LOW VOLTAGE8-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL6295CVZ-T | 功能描述:IC FUEL GAUGE LOW VOLTAGE8-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6295EVAL1 | 制造商:Intersil Corporation 功能描述:LOW VOLT FUEL GAUGE - Bulk |
| ISL6296 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:FlexiHash For Battery Authentication |
| ISL6296_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:FlexiHash⑩ For Battery Authentication |
發布緊急采購，3分鐘左右您將得到回復。