- 您現在的位置：買賣IC網 > PDF目錄296253 > ISL6292-1CR5-T (INTERSIL CORP) Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6292-1CR5-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-TSSOP -40 to 85 |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封裝： | 5 X 5 MM, PLASTIC, MO-220VHHB, QFN-16 |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 550K |
| 代理商： | ISL6292-1CR5-T |
15
FN9105.9
December 17, 2007
Input and Output Capacitor Selection
Typically any type of capacitors can be used for the input
and the output. Use of a 0.47F or higher value ceramic
capacitor for the input is recommended. When the battery is
attached to the charger, the output capacitor can be any
ceramic type with the value higher than 0.1F. However, if
there is a chance the charger will be used as an LDO linear
regulator, a 10F tantalum capacitor is recommended.
Current-Limited Adapter
Figure 24 shows the ideal current-voltage characteristics of
a current-limited adapter. VNL is the no-load adapter output
voltage and VFL is the full load voltage at the current limit
ILIM. Before its output current reaches the limit ILIM, the
adapter presents the characteristics of a voltage source. The
slope rO represents the output resistance of the voltage
supply. For a well regulated supply, the output resistance
can be very small, but some adapters naturally have a
certain amount of output resistance.
The adapter is equivalent to a current source when running
in the constant-current region. Being a current source, its
output voltage is dependent on the load, which, in this case,
is the charger and the battery. As the battery is being
charged, the adapter output rises from a lower voltage in the
current-voltage characteristics curve, such as point A, to
higher voltage until reaching the breaking point B, as shown
in Figure 24.
The adapter is equivalent to a voltage source with output
resistance when running in the constant-voltage region;
because of this characteristic. As the charge current drops,
the adapter output moves from point B to point C, shown in
Figure 24.
The battery pack can be approximated as an ideal cell with a
lumped-sum resistance in series, also shown in Figure 24.
The ISL6292 charger sits between the adapter and the
battery.
Working with Current-Limited Adapter
As described earlier, the ISL6292 minimizes the thermal
dissipation when running off a current-limited AC adapter, as
shown in Figure 18. The thermal dissipation can be further
reduced when the adapter is properly designed. The
following demonstrates that the thermal dissipation can be
minimized if the adapter output reaches the full-load output
voltage (point B in Figure 24) before the battery pack voltage
reaches the final charge voltage (4.1V or 4.2V). The
assumptions for the following discussion are: the adapter
current limit = 750mA, the battery pack equivalent
resistance = 200m
Ω, and the charger ON-resistance is
350m
Ω.
When charging in the constant-current region, the pass
element in the charger is fully turned on. The charger is
equivalent to the ON-resistance of the internal P-Channel
MOSFET. The entire charging system is equivalent to the
circuit shown in Figure 25A. The charge current is the
constant current limit ILIM, and the adapter output voltage
can be easily found out as calculated in Equation 13:
where VPACK is the battery pack voltage. The power
dissipation in the charger is given in Equation 2, where
ICHARGE = ILIM.
A critical condition of the adapter design is that the adapter
output reaches point B in Figure 24 at the same time as the
battery pack voltage reaches the final charge voltage (4.1V
or 4.2V), that is:
For example, if the final charge voltage is 4.2V, the rDS(ON)
is 350m
Ω, and the current limit ILIM is 750mA, the critical
adapter full-load voltage is 4.4625V.
When the above condition is true, the charger enters the
constant-voltage mode simultaneously as the adapter exits
the current-limit mode. The equivalent charging system is
shown in Figure 25C. Since the charge current drops at a
higher rate in the constant-voltage mode than the increase
rate of the adapter voltage, the power dissipation decreases
as the charge current decreases. Therefore, the worst case
thermal dissipation occurs in the constant-current charge
mode. Figure 25A shows the I-V curves of the adapter
output, the battery pack voltage and the cell voltage during
the charge. The 5.9V no-load voltage is just an example
value higher than the full-load voltage. The cell voltage
4.05V uses the assumption that the pack resistance is
200m
Ω. Figure 26A illustrates the adapter voltage, battery
pack voltage, the charge current and the power dissipation in
the charger respectively in the time domain.
High
Low
Charging in one of the three modes
Low
High
Fault
TABLE 2. STATUS INDICATIONS
FAULT STATUS
INDICATION
*Both outputs are pulled up with external resistors.
FIGURE 24. THE IDEAL I-V CHARACTERISTICS OF A
CURRENT LIMITED ADAPTER
V
NL
V
FL
I
LIM
r
O
V
NL
I
LIM
r
O = (VNL - VFL)/ILIM
V
PACK
V
CELL
R
PACK
A
B
C
V
Adapter
I
LIM rDS ON
() VPACK
+
=
(EQ. 13)
V
Critical
I
LIM rDS ON
()
V
CH
+
=
(EQ. 14)
ISL6292
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6406CVZ | Quadruple 2-Input Positive-NAND Gates 14-SO -40 to 85 |
| ISL6426CB | Triple 3-Input Positive-NAND Gates 14-SOIC -40 to 85 |
| ISL6426CBZ | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6426CR | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6426CRZ | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6292-1CR5Z | 功能描述:電池管理 LD VER OF ISL6292-1C R5 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| ISL6292-1CR5Z-T | 功能描述:電池管理 LD VER OF ISL6292-1C R5-T RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| ISL6292-2CR3 | 功能描述:IC CHARGER LI-ION 2.4V 10-DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6292-2CR3-T | 功能描述:IC BATT CHRGR LI-ION 4.2V 10-DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6292-2CR3Z | 功能描述:電池管理 LD VER OF ISL6292-2C R3 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。