- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6269A (Intersil Corporation) High-Performance Notebook PWM Controller(高性能筆記本PWM控制器) PDF資料下載
參數資料
| 型號： | ISL6269A |
| 廠商： | Intersil Corporation |
| 英文描述： | High-Performance Notebook PWM Controller(高性能筆記本PWM控制器) |
| 中文描述： | 高性能筆記本PWM控制器（高性能筆記本的PWM控制器） |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 313K |
| 代理商： | ISL6269A |
9
FN9253.2
May 30, 2007
while the LG gate-driver pin is high, for eight consecutive
PWM pulses. The converter will return to CCM on the
following cycle after the PHASE pin detects negative
voltage, indicating that the body diode of the low-side
MOSFET is conducting positive inductor current.
Overcurrent and Short-Circuit Protection
The overcurrent protection (OCP) and short circuit protection
(SCP) setpoint is programmed with resistor R
SEN
that is
connected across the ISEN and PHASE pins. The PHASE
pin is connected to the drain terminal of the low-side
MOSFET.
The SCP setpoint is internally set to twice the OCP setpoint.
When an OCP or SCP fault is detected, the PGOOD pin will
pulldown to 30
Ω
and latch off the converter. The fault will
remain latched until the EN pin has been pulled below the
falling EN threshold voltage V
ENTHF
or if V
VCC
has decayed
below the falling POR threshold voltage
V
VCC_THF
.
The OCP circuit does not directly detect the DC load current
leaving the converter. The OCP circuit detects the peak of
positive-flowing output inductor current. The low-side
MOSFET drain current I
D
is assumed to be equal to the
positive output inductor current when the high-side MOSFET
is off. The inductor current develops a negative voltage
across the r
DS(ON)
of the low-side MOSFET that is
measured shortly after the LG gate-driver output goes high.
The ISEN pin sources the OCP sense current I
SEN,
through
the OCP programming resistor R
SEN,
forcing the ISEN pin to
zero volts with respect to the GND pin. The negative voltage
across the PHASE and GND pins is nulled by the voltage
dropped across R
SEN
as I
SEN
conducts through it. An OCP
fault occurs if I
SEN
rises above the OCP threshold current
I
OC
while attempting to null the negative voltage across the
PHASE and GND pins. I
SEN
must exceed I
OC
on all the
PWM pulses that occur within 20μs. If I
SEN
falls below I
OC
on a PWM pulse before 20μs has elapsed, the timer will be
reset. An SCP fault will occur within 10μs when I
SEN
exceeds twice I
OC.
The relationship between I
D
and I
SEN
is
written as:
The value of R
SEN
is then written as:
Where:
- R
SEN
(
Ω
) is the resistor used to program the
overcurrent setpoint
- I
SEN
is the current sense current that is sourced from
the ISEN pin
- I
OC
is the I
SEN
threshold current sourced from the ISEN
pin that will activate the OCP circuit
- I
FL
is the maximum continuous DC load current
- I
PP
is the inductor peak-to-peak ripple current
- OC
SP
is the desired overcurrent setpoint expressed as
a multiplier relative to I
FL
Overvoltage Protection
When an OVP fault is detected, the PGOOD pin will pull
down to 60
Ω
and latch-off the converter. The OVP fault will
remain latched until V
VCC
has decayed below the falling
POR threshold voltage
V
VCC_THF
.
The OVP fault detection circuit triggers after the voltage
across the FB and GND pins has increased above the rising
overvoltage threshold V
OVR.
Although the converter has
latched-off in response to an OVP fault, the LG gate-driver
output will retain the ability to toggle the low-side MOSFET
on and off, in response to the output voltage transversing the
V
OVR
and V
OVF
thresholds.
Undervoltage Protection
When a UVP fault is detected, the PGOOD pin will pull down
to 95
Ω
and latch-off the converter. The fault will remain
latched until the EN pin has been pulled below the falling EN
threshold voltage V
ENTHF
or if V
VCC
has decayed below the
falling POR threshold voltage
V
VCC_THF
.
The UVP fault
detection circuit triggers after the voltage across the FB and
GND pins has fallen below the undervoltage threshold V
UV
.
Over-Temperature
When the temperature of the ISL6269A increases above the
rising threshold temperature T
OTR
, the IC will enter an OTP
state that suspends the PWM , forcing the LG and UG
gate-driver outputs low. The status of the PGOOD pin does
not change nor does the converter latch-off. The PWM
remains suspended until the IC temperature falls below the
hysteresis temperature T
OTHYS
at which time normal PWM
operation resumes. The OTP state can be reset if the EN pin
is pulled below the falling EN threshold voltage V
ENTHF
or if
V
VCC
decays below the falling POR threshold voltage
V
VCC_THF
. All other protection circuits function normally
during OTP. It is likely that the IC will detect an UVP fault
because in the absence of PWM, the output voltage
immediately decays below the undervoltage threshold V
UV
;
the PGOOD pin will pulldown to 95
Ω
and latch-off the
converter. The UVP fault will remain latched until the EN pin
has been pulled below the falling EN threshold voltage
V
ENTHF
or if V
VCC
has decayed below the falling POR
threshold voltage
V
VCC_THF
.
I
SEN
R
SEN
I
D
r
DS ON
(
)
=
(EQ. 3)
(EQ. 4)
R
SEN
I
----------------------------------------------------------------------------
I
--------
+
OC
OC
r
)
=
ISL6269A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6271ACRZ | Integrated XScale Regulator |
| ISL6271ACRZ-T | Integrated XScale Regulator |
| ISL6271A | Integrated XScale Regulator |
| ISL6271ACR | Integrated XScale Regulator |
| ISL6271ACR-T | Integrated XScale Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6269ACRZ | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6269ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6269ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6269ACRZ-T WITH GOLD BOND WIRE ONLY, T&R - Tape and Reel |
| ISL6269AEVAL2 | 制造商:Intersil Corporation 功能描述:ISL6269A EVALUATION BOARD 2 - Bulk |
| ISL6269AEVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6269A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。