- 您現在的位置：買賣IC網 > PDF目錄383142 > ISL6223EVAL2 (Intersil Corporation) Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller PDF資料下載
參數資料
| 型號： | ISL6223EVAL2 |
| 廠商： | Intersil Corporation |
| 英文描述： | Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| 中文描述： | 移動微處理器核心電壓調節器的多相降壓PWM控制器 |
| 文件頁數： | 1/15頁 |
| 文件大?。?/td> | 402K |
| 代理商： | ISL6223EVAL2 |
1
FN9013
ISL6223
Mobile Microprocessor CORE Voltage
Regulator Multi-Phase Buck PWM
Controller
The ISL6223 multi-phase PWM control IC together with its
companion gate drivers, the HIP6601, HIP6602 or HIP6603
and Intersil MOSFETs provides a precision voltage
regulation system for advanced mobile microprocessors. A
single-stage regulator that directly converts a battery voltage
to a microprocessor core voltage can be designed when high
voltage drivers are employed. Multiphase power conversion
is a marked departure from earlier single phase converter
configurations previously employed to satisfy the ever
increasing current demands of modern microprocessors.
Multi-phase converters, by distributing the power and load
current, result in smaller and lower cost transistors with
fewer input and output capacitors. These reductions accrue
from the higher effective conversion frequency with higher
frequency ripple current due to the phase interleaving
process of this topology. For example, a two phase converter
operating at 350kHz will have a ripple frequency of 700kHz.
Moreover, greater converter bandwidth of this design results
in faster response to load transients.
Outstanding features of this controller IC include
programmable VID codes from the microprocessor that
range from 0.925V to 2.00V with a system accuracy of
±
1%.
Pull up currents on these VID pins eliminates the need for
external pull up resistors. In addition “droop” compensation,
used to reduce the overshoot or undershoot of the CORE
voltage, is easily programmed with a single resistor.
Another feature of this controller IC is the PGOOD monitor
circuit which is held low until the CORE voltage increases,
during its Soft-Start sequence, to 0.9V. Overvoltage, the
CORE voltage going above 2.35V, results in the converter
shutting down and turning the lower MOSFETs ON to clamp
and protect the microprocessor. Under voltage is also
detected and results in PGOOD low if the CORE voltage falls
below 0.9V. Overcurrent protection reduces the regulator
current to less than 25% of the programmed trip value. An
external capacitor connected to the DACOUT pin and
ground slows down the transition of the DAC output to avoid
triggering the overcurrent protection when the VID code
changes. These features provide monitoring and protection
for the microprocessor and power system.
Features
Mobile VID Compatible Multi-Phase Power Conversion
Precision Channel Current Sharing
- Loss Less Current Sampling - Uses r
DS(ON)
Precision CORE Voltage Regulation
-
±
1% System Accuracy Over Temperature
Microprocessor Voltage Identification Input
- 5-Bit VID Input
- 1.30V to 2.00V in 50mV Steps
- 0.925V to 1.275V in 25mV Steps
- Programmable “Droop” Voltage
Fast Transient Recovery Time
Over Current Protection
High Ripple Frequency (Channel Frequency Times
Number of Channels, Two). . . . . . . . . . . .100kHz to 3MHz
Pinout
ISL6223 (SSOP)
TOP VIEW
Ordering Information
PART NUMBER
TEMP. (
o
C)
PACKAGE
PKG. NO.
ISL6223CA
0 to 70
20 Ld SSOP
M20.15
ISL6223CA-T
20 Ld SSOP Tape and Reel
ISL6223EVAL1
Evaluation Platform
ISL6223EVAL2
Evaluation Platform
11
12
13
14
15
16
17
18
20
19
10
9
8
7
6
5
4
3
2
1
VID4
VID3
VID2
VID1
VID0
FS/DIS
PWM2
PGOOD
DACOUT
NC
ISEN1
V
CC
GND
NC
FB
NC
VSEN
COMP
PWM1
ISEN2
Data Sheet
February 2003
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6224CA-T | Single Output Mobile-Friendly PWM Controller |
| ISL6224CAZA-T | ER 5C 2#16 3#12 PIN PLUG |
| ISL6224CAZ-T | KJ 66C 66#22D SKT RECP |
| ISL6224CAZ | Single Output Mobile-Friendly PWM Controller |
| ISL6224 | Single Output Mobile-Friendly PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6224 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Output Mobile-Friendly PWM Controller |
| ISL6224_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Output Mobile-Friendly PWM Controller |
| ISL6224CA | 功能描述:電流型 PWM 控制器 Mobile-Friendly RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6224CA-T | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6224CAZ | 功能描述:電流型 PWM 控制器 MOBILE PWM CNTRLR 16-PIN SSOP RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。