- 您現在的位置：買賣IC網 > PDF目錄383141 > ISL6161CB-T (INTERSIL CORP) Dual Power Distribution Controller PDF資料下載
參數資料
| 型號： | ISL6161CB-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Power Distribution Controller |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| 封裝： | PLASTIC, MS-012AB, SOIC-14 |
| 文件頁數： | 1/10頁 |
| 文件大?。?/td> | 224K |
| 代理商： | ISL6161CB-T |
1
FN9104.3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2001, 2003-2004. All Rights Reserved. Hot Plug is a trademark of Core International, Inc.
All other trademarks mentioned are the property of their respective owners.
ISL6161
Dual Power Distribution Controller
The ISL6161 is a HOT SWAP dual supply power distribution
controller that can be used in PCI-Express applications.
Two external N-Channel MOSFETs are driven to distribute
and control power while providing load fault isolation. At turn-
on, the gate of each external N-Channel MOSFET is
charged with a 10
μ
A current source. Capacitors on each
gate (see the Typical Application Diagram), create a
programmable ramp (soft turn-on) to control inrush currents.
A built in charge pump supplies the gate drive for the 12V
supply N-Channel MOSFET switch.
Over current protection is facilitated by two external current
sense resistors and FETs. When the current through either
resistor exceeds the user programmed value the controller
enters the current regulation mode. The time-out capacitor,
C
TIM
, starts charging as the controller enters the time out
period. Once C
TIM
charges to a 2V threshold, both the
N-Channel MOSFETs are latched off. In the event of a hard
and fast fault of at least three times the programmed current
limit level, the N-Channel MOSFET gates are pulled low
immediately before entering the time out period. The
controller is reset by a rising edge on the ENABLE pin.
The ISL6161 constantly monitors both output voltages and
reports either one being low on the PGOOD output as a low.
The 12V PGOOD Vth is ~10.8V and the 3.3V Vth is ~2.8V
nominally.
Features
HOT SWAP Dual Power Distribution and Control for +12V
and +3.3V
Provides Fault Isolation
Programmable Current Regulation Level
Programmable Time Out
Charge Pump Allows the Use of N-Channel MOSFETs
Power Good and Over Current Latch Indicators
Adjustable Turn-On Ramp
Protection During Turn-On
Two Levels of Current Limit Detection Provide Fast
Response to Varying Fault Conditions
1
μ
s Response Time to Dead Short
3
μ
s Response Time to 200% Current Overshoot
Pb-free available
Applications
PCI-Express Applications
Power Distribution and Control
Hot Plug, Hot Swap Components
PART NUMBER
TEMP. RANGE
(
o
C)
PACKAGE
PKG.
DWG. #
ISL6161CB
-0 to 70
14 Ld SOIC
M14.15
ISL6161CBZA
(See Note)
-0 to 70
14 Ld SOIC
(Pb-free)
M14.15
*Add “-T” suffix to part number for tape and reel packaging.
NOTE: Intersil Pb-free products employ special Pb-free material sets; molding
compounds/die attach materials and 100% matte tin plate termination finish, which
is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J Std-020B.
Pinout
ISL6161 (SOIC)
TOP VIEW
Typical Application Diagram
8
9
10
11
12
14
13
7
6
5
4
3
2
1
12VS
12VG
V
DD
NC
ENABLE
3VG
3VS
12VISEN
GND
C
PUMP
C
TIM
PGOOD
R
ILIM
3VISEN
12VS
12VG
V
DD
ENABLE
3VG
3VS
PGOOD
12VISEN
R
ILIM
GND
C
TIM
C
PUMP
3ISEN
ISL6161
12V
R
LOAD
R
ILIM
C
TIM
ENABLE
INPUT
C
PUMP
R
SENSE
3.3V
R
LOAD
R
SENSE
3.3V
OPTIONAL
R
FILTER
C
FILTER
V
DD
C
GATE
C
GATE
Data Sheet
July 2004
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6161 | Octal D-Type Transparent Latches With 3-State Outputs 20-SO -40 to 85 |
| ISL6161CB | Dual Power Distribution Controller |
| ISL6161CBZA | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6161CBZA-T | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6173DRZA | Dual Low Voltage Hot Swap Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6161CBZA | 功能描述:IC CTLR PWR DISTRIB DUAL 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| ISL6161CBZA-T | 功能描述:IC CTLR PWR DISTRIB DUAL 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| ISL6161IBZA | 功能描述:IC CTRLR PWR DISTRIB DUAL 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| ISL6161IBZA-T | 功能描述:IC CTRLR PWR DISTRIB DUAL 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| ISL6172DRZA | 功能描述:熱插拔功率分布 W/ANNEAL DL LV HOT SWAP CNTRLR 0-85 TMP RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。