- 您現在的位置：買賣IC網 > PDF目錄384523 > ISL59830IA-T7 (INTERSIL CORP) True Single Supply Video Driver PDF資料下載
參數資料
| 型號： | ISL59830IA-T7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | True Single Supply Video Driver |
| 中文描述： | 3 CHANNEL, VIDEO AMPLIFIER, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, QSOP-16 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 333K |
| 代理商： | ISL59830IA-T7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁
13
FN7489.6
May 4, 2006
the EN pin. The applied logic signal is relative to GND pin.
Letting the EN pin float or applying a signal that is less than
0.8V above GND will enable the amplifier. The amplifier will
be disabled when the signal at EN pin is 2V above GND. The
V
EE
charge pump remains active.
Output Drive Capability
The ISL59830 does not have internal short-circuit protection
circuitry. A short-circuit current of 80mA sourcing and 150mA
sinking for the output is connected to half way between the
rails with a 10
Ω
resistor. If the output is shorted indefinitely,
the power dissipation could easily increase such that the part
will be destroyed. Maximum reliability is maintained if the
output current never exceeds ±40mA, after which the
electro-migration limit of the process will be exceeded and
the part will be damaged. This limit is set by the design of the
internal metal interconnections.
Power Dissipation
With the high output drive capability of the ISL59830, it is
possible to exceed the 150°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for an application to determine if load conditions
or package types need to be modified to assure operation of
the amplifier in a safe operating area.
The maximum power dissipation allowed in a package is
determined according to:
Where:
T
JMAX
= Maximum junction temperature
T
AMAX
= Maximum ambient temperature
Θ
JA
= Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
for sourcing:
for sinking:
Where:
V
S
= Supply voltage
I
SMAX
= Maximum quiescent supply current
V
OUT
= Maximum output voltage of the application
R
LOAD
= Load resistance tied to ground
I
LOAD
= Load current
i = Number of output channels
By setting the two P
DMAX
equations equal to each other, we
can solve the output current and R
LOAD
to avoid the device
overheat.
Power Supply Bypassing and Printed Circuit
Board Layout
Strip line design techniques are recommended for the input
and output signal traces. As with any high frequency device,
a good printed circuit board layout is necessary for optimum
performance. Lead lengths should be as short as possible.
The power supply pin must be well bypassed to reduce the
risk of oscillation. For normal single supply operation, where
the V
S
- pin is connected to the ground plane, a single 4.7μF
tantalum capacitor in parallel with a 0.1μF ceramic capacitor
from V
S
+ to GND will suffice. This same capacitor
combination should be placed at each supply pin to ground if
split-internal supplies are to be used. In this case, the V
S
-
pin becomes the negative supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire-wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier's inverting input pin is also very important.
PD
MAX
T
--------------------------------------------
T
JA
–
=
PD
MAX
V
S
I
SMAX
V
S
V
OUT
i
–
(
)
+
×
V
i
L
-----------------
×
=
PD
MAX
V
S
I
SMAX
V
OUT
i
V
S
–
(
)
+
×
I
LOAD
i
×
=
ISL59830
相關PDF資料 |
PDF描述 |
|---|---|
| ISL59830IAZ-T7 | True Single Supply Video Driver |
| ISL59885ISZR5260 | Auto-Adjusting Sync Separator for HD and SD Video |
| ISL59885ISZ-T7R5260 | Auto-Adjusting Sync Separator for HD and SD Video |
| ISL59910 | Triple Differential Receiver/Equalizer(三路差分接收器/均衡器) |
| ISL59913 | Triple Differential Receiver/Equalizer(三路差分接收器/均衡器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59830IAZ | 功能描述:IC DRIVER VIDEO SGL 3.3V 16QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59830IAZ-EVAL | 制造商:Intersil Corporation 功能描述:TRUE SGL SUPPLY VID DRVR - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL59830 制造商:Intersil 功能描述:ISL90843W LW NOISE LW PWR I2C BUS 256 |
| ISL59830IAZ-T13 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59830IAZ-T7 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59831 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Supply Video Driver with Reconstruction Filter and Charge Pump |
發布緊急采購，3分鐘左右您將得到回復。