- 您現在的位置：買賣IC網 > PDF目錄16332 > ISL59448EVAL1Z (Intersil)EVAL BOARD 1 FOR ISL59448 PDF資料下載
參數資料
| 型號： | ISL59448EVAL1Z |
| 廠商： | Intersil |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD 1 FOR ISL59448 |
| 標準包裝： | 1 |
| 系列： | * |
12
FN6160.2
March 29, 2006
control signal rise and fall times less than 10ns the use of
termination resistors close to the part will minimize transients
coupled to the output.
Power-up Considerations
The ESD protection circuits use internal diodes from all pins
the V+ and V- supplies. In addition, a dV/dT- triggered clamp
is connected between the V+ and V- pins, as shown in the
Equivalent Circuits 1 through 4 section of the Pin Description
table. The dV/dT triggered clamp imposes a maximum
supply turn-on slew rate of 1V/s. Damaging currents can
flow for power supply rates-of-rise in excess of 1V/s, such
as during hot plugging. Under these conditions, additional
methods should be employed to ensure the rate of rise is not
exceeded.
Consideration must be given to the order in which power is
applied to the V+ and V- pins, as well as analog and logic
input pins. Schottky diodes (Motorola MBR0550T or
equivalent) connected from V+ to ground and V- to ground
(Figure 4) will shunt damaging currents away from the
internal V+ and V- ESD diodes in the event that the V+
supply is applied to the device before the V- supply.
If positive voltages are applied to the logic or analog video
input pins before V+ is applied, current will flow through the
internal ESD diodes to the V+ pin. The presence of large
decoupling capacitors and the loading effect of other circuits
connected to V+, can result in damaging currents through
the ESD diodes and other active circuits within the device.
Therefore, adequate current limiting on the digital and
analog inputs is needed to prevent damage during the time
the voltages on these inputs are more positive than V+.
HIZ State
An internal pull-down resistor ensures the device will be
active with no connection to the HIZ pin. The HIZ state is
established within approximately 15ns (Figure 14) by placing
a logic high (>2V) on the HIZ pin. If the HIZ state is selected,
the output impedance is ~1000
(Figure 6). The supply
current during this state is same as the active state.
ENABLE and Power-down States
The enable pin is active low. An internal pull-down resistor
ensures the device will be active with no connection to the
ENABLE pin. The Power-down state is established within
approximately 200ns (Figure 22), if a logic high (>2V) is
placed on the ENABLE pin. In the power-down state, the
output has no leakage but has a large variable capacitance
(on the order of 15pF), and is capable of being back-driven.
Under this condition, large incoming slew rates can cause
fault currents of tens of mA. Therefore, the parallel
connection of multiple outputs is not recommended unless
the application can tolerate the limited powerdown output
impedance.
LE State
The ISL59448 is equipped with a Latch Enable pin. A logic
high (>2V) on the LE pin latches the last logic state. This
logic state is preserved when cycling HIZ or ENABLE
functions.
Limiting the Output Current
No output short circuit current limit exists on these parts. All
applications need to limit the output current to less than
50mA. Adequate thermal heat sinking of the parts is also
required.
V+
V-
V+
V-
V+
V-
LOGIC
CONTROL
GND
IN0
IN1
S0
OUT
EXTERNAL
CIRCUITS
SCHOTTKY
PROTECTION
V+
V-
POWER
GND
SIGNAL
LOGIC
V+ SUPPLY
V- SUPPLY
DE-COUPLING
CAPS
FIGURE 28. SCHOTTKY PROTECTION CIRCUIT
ISL59448
相關PDF資料 |
PDF描述 |
|---|---|
| EYM08DRMD-S664 | CONN EDGECARD 16POS .156 WW |
| 2-6278876-0 | C/A 50.125UM RIS MTRJ 20M1 |
| VE-B1T-EY-S | CONVERTER MOD DC/DC 6.5V 50W |
| VE-B1N-EY-S | CONVERTER MOD DC/DC 18.5V 50W |
| ECM22DRXN | CONN EDGECARD 44POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59448IAZ | 功能描述:IC AMP TRIPLE MUX 500MHZ 24-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59448IAZ-T7 | 功能描述:IC AMP MUX 2:1 500MHZ 24-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59450 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Multiformat Video Crosspoint with Integrated Sync Separator |
| ISL59450IQZ | 功能描述:IC SWITCH VID CRSSPNT 128-MQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| ISL59450IQZ-EVAL | 制造商:Intersil Corporation 功能描述:ISL59450IQZ-EVAL EVALUATION BOARD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。