- 您現在的位置：買賣IC網 > PDF目錄2081 > ISL59440IAZ-T7 (Intersil)IC AMP 400MHZ MULTIPLEX 16-QSOP PDF資料下載
參數資料
| 型號： | ISL59440IAZ-T7 |
| 廠商： | Intersil |
| 文件頁數： | 2/12頁 |
| 文件大小： | 0K |
| 描述： | IC AMP 400MHZ MULTIPLEX 16-QSOP |
| 標準包裝： | 1 |
| 應用： | 4:1 多路復用器-放大器 |
| 電路數： | 1 |
| -3db帶寬： | 400MHz |
| 轉換速率： | 1470 V/µs |
| 電流 - 電源： | 14.5mA |
| 電流 - 輸出 / 通道： | 130mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | ISL59440IAZ-T7DKR |
10
FN6162.2
October 10, 2007
GROUND CONNECTIONS
For the best isolation and crosstalk rejection, the GND pin
and NIC pins must connect to the GND plane.
CONTROL SIGNALS
S0, S1, ENABLE, HIZ - These pins are TTL/CMOS
compatible control inputs. The S0 pin selects which one of
the inputs connect to the output. The ENABLE, HIZ pins are
used to disable the part to save power and three-state the
output amplifiers, respectively. For control signal rise and fall
times less than 10ns the use of termination resistors close to
the part will minimize transients coupled to the output.
POWER-UP CONSIDERATIONS
The ESD protection circuits use internal diodes from all pins
the V+ and V- supplies. In addition, a dV/dT- triggered clamp
is connected between the V+ and V- pins, as shown in the
Equivalent Circuits 1 through 4 section of the “Pin
Descriptions” on page 8. The dV/dT triggered clamp
imposes a maximum supply turn-on slew rate of 1V/s.
Damaging currents can flow for power supply rates-of-rise in
excess of 1V/s, such as during hot plugging. Under these
conditions, additional methods should be employed to
ensure the rate of rise is not exceeded.
Consideration must be given to the order in which power is
applied to the V+ and V- pins, as well as analog and logic
input pins. Schottky diodes (Motorola MBR0550T or
equivalent) connected from V+ to ground and V- to ground
(Figure 26) will shunt damaging currents away from the
internal V+ and V- ESD diodes in the event that the V+
supply is applied to the device before the V- supply.
If positive voltages are applied to the logic or analog video
input pins before V+ is applied, current will flow through the
internal ESD diodes to the V+ pin. The presence of large
decoupling capacitors and the loading effect of other circuits
connected to V+, can result in damaging currents through
the ESD diodes and other active circuits within the device.
Therefore, adequate current limiting on the digital and
analog inputs is needed to prevent damage during the time
the voltages on these inputs are more positive than V+.
HIZ STATE
An internal pull-down resistor connected to the HIZ pin
ensures the device will be active with no connection to the
HIZ pin. The HIZ state is established within approximately
30ns (Figure 18) by placing a logic high (> 2V) on the HIZ
pin. If the HIZ state is selected, the output is a high
impedance 1.4M
Ω. Use this state to control the logic when
more than one mux shares a common output.
In the HIZ state the output is three-stated, and maintains its
high Z even in the presence of high slew rates. The supply
current during this state is basically the same as the active
state.
ENABLE AND POWER DOWN STATES
The enable pin is active low. An internal pull-down resistor
ensures the device will be active with no connection to the
ENABLE pin. The Power Down state is established when a
logic high (>2V) is placed on the ENABLE pin. In the Power
Down state, the output has no leakage but has a large
capacitance (on the order of 15pF), and is capable of being
back-driven. Under this condition, large incoming slew rates
can cause fault currents of tens of mA. Do not use this
state as a high Z state for applications driving more than
one mux on a common output.
LIMITING THE OUTPUT CURRENT
No output short circuit current limit exists on this part. All
applications need to limit the output current to less than
50mA. Adequate thermal heat sinking of the parts is also
required.
V+
V-
V+
V-
V+
V-
LOGIC
CONTROL
GND
IN0
IN1
S0
OUT
EXTERNAL
CIRCUITS
SCHOTTKY
PROTECTION
V+
V-
POWER
GND
SIGNAL
LOGIC
V+ SUPPLY
V- SUPPLY
DE-COUPLING
CAPS
FIGURE 26. SCHOTTKY PROTECTION CIRCUIT
ISL59440
相關PDF資料 |
PDF描述 |
|---|---|
| ISL59441IA-T7 | IC AMP MULTIPLEX 900MHZ 16-QSOP |
| ISL59442IBZ | IC CROSSPOINT SW 1GHZ 4X1 14SOIC |
| ISL59444IBZ-T7 | IC AMP MULTIPLEX 1GHZ 16SOIC |
| ISL59446IRZ | IC AMP MUX 4:1 500MHZ 32-QFN |
| ISL59448IAZ-T7 | IC AMP MUX 2:1 500MHZ 24-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59441 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:900MHz Multiplexing Amplifier |
| ISL59441IA | 功能描述:IC AMP MULTIPLEX 900MHZ 16-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59441IA-T13 | 功能描述:IC AMP MULTIPLEX 900MHZ 16-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59441IA-T7 | 功能描述:IC AMP MULTIPLEX 900MHZ 16-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59441IAZ | 功能描述:視頻放大器 ISL8200M EVALRD 1 23LD RHS COMPLIA RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。