- 您現在的位置：買賣IC網 > PDF目錄2081 > ISL59123IIZ-T7 (Intersil)IC VIDEO DRVR TRI-CHN LPF 9WLCSP PDF資料下載
參數資料
| 型號： | ISL59123IIZ-T7 |
| 廠商： | Intersil |
| 文件頁數： | 10/10頁 |
| 文件大小： | 0K |
| 描述： | IC VIDEO DRVR TRI-CHN LPF 9WLCSP |
| 標準包裝： | 3,000 |
| 應用： | 重構濾波器 |
| 輸出類型： | 滿擺幅 |
| 電路數： | 3 |
| -3db帶寬： | 18MHz |
| 轉換速率： | 60 V/µs |
| 電流 - 電源： | 4mA |
| 電流 - 輸出 / 通道： | 200mA |
| 電壓 - 電源，單路/雙路(±)： | 2.5 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 9-UFBGA，WLCSP |
| 供應商設備封裝： | 9-CSP（1.45x1.45） |
| 包裝： | 帶卷 (TR) |
9
FN6432.1
April 4, 2007
Application Information
The ISL59123 is a single-supply rail-to-rail triple video low-
pass filter and amplifier with a -3dB bandwidth of 18MHz. It
provides anti-aliasing for component, s-video, and
composite video signals. Its small size and low power make
the ISL59123 ideal for portable video applications.
The Sallen Key Low Pass Filter
The Sallen Key is a classic low pass configuration. This
provides a very stable low pass function, and in the case of
the ISL59123, a three-pole roll-off at 18MHz. The three-pole
function is accomplished with an RC low pass network placed
in series with and before the Sallen Key. The first pole is
formed by an RC network (including the impedance of the
source driving the ISL59123), with poles two and three
generated by a Sallen Key, creating a three-pole roll-off
characteristic at 18MHz.
Output Coupling
The ISL59123 can be AC or DC coupled to its output. When
AC coupled, a 220F coupling capacitor is recommended to
ensure that low frequencies are passed, preventing video
“tilt” or “droop” across a line.
Output Drive Capability
The ISL59123 does not have internal short circuit protection
circuitry. If the output is shorted indefinitely, the power
dissipation could easily overheat the die or the current could
eventually compromise metal integrity. Maximum reliability is
maintained if the output current never exceeds ±40mA. This
limit is set by the design of the internal metal interconnect. Note
that for transient short circuits, the part is robust.
Short circuit protection can be provided externally with a back
match resistor in series with the output placed close as possible
to the output pin. In video applications this would be a 75
Ω
resistor and will provide adequate short circuit protection to the
device. Care should still be taken not to stress the device with a
short at the output.
Power Dissipation
With the high output drive capability of the ISL59123, it is
possible to exceed the +125°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for an application to determine if load conditions
or package types need to be modified to assure operation of
the amplifier in a safe operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 1:
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
for sourcing use Equation 2:
for sinking use Equation 3:
Where:
VS = Supply voltage
ISMAX = Maximum quiescent supply current
VOUT = Maximum output voltage of the application
RLOAD = Load resistance tied to ground
ILOAD = Load current
Power Supply Bypassing Printed Circuit Board
Layout
As with any modern operational amplifier, a good printed
circuit board layout is necessary for optimum performance.
Lead lengths should be as short as possible. The power
supply pin must be well bypassed to reduce the risk of
oscillation. For normal single supply operation, a single
4.7F tantalum capacitor in parallel with a 0.1F ceramic
capacitor from VDD to GND will suffice.
Printed Circuit Board Layout
For good AC performance, parasitic capacitance should be
kept to minimum. Use of wire wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance.
PD
MAX
T
JMAX
T
AMAX
–
θ
JA
---------------------------------------------
=
(EQ. 1)
PD
MAX
V
S
I
SMAX
V
S
V
OUT
–
()
+
×
V
OUT
R
L
----------------
×
=
(EQ. 2)
PD
MAX
V
S
I
SMAX
V
OUT
V
S
–
()
+
×
I
LOAD
×
=
(EQ. 3)
ISL59123
相關PDF資料 |
PDF描述 |
|---|---|
| ISL59311IRZ | IC VIDEO AMP TRI DIFF 32-QFN |
| ISL59420IUZ | IC AMP MULTIPLEX 400MHZ 10-MSOP |
| ISL59421IUZ | IC AMP MULTIPLEX 865MHZ 10-MSOP |
| ISL59424IR | IC MUX AMPLIFIER TRPL 1GHZ 24QFN |
| ISL59440IAZ-T7 | IC AMP 400MHZ MULTIPLEX 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59151IRZ-EVALZ | 制造商:Intersil Corporation 功能描述:ISL59151IRZ-EVALZ (PB-FREE ) EVALUATION BOARD - ROHS COMPLIA - Bulk |
| ISL5927 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 14-Bit, +3.3V, 260+MSPS, High Speed D/A Converter |
| ISL5927EVAL1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 14-Bit, +3.3V, 260+MSPS, High Speed D/A Converter |
| ISL5927IN | 功能描述:IC DAC 14BIT DUAL 260MSPS 48LQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| ISL5927INZ | 功能描述:IC DAC 14BIT CMOS DUAL 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。