- 您現在的位置：買賣IC網 > PDF目錄3298 > ISL55290IUZ-T13 (Intersil)IC OPAMP LP DUAL ULT LN 10-MSOP PDF資料下載
參數資料
| 型號： | ISL55290IUZ-T13 |
| 廠商： | Intersil |
| 文件頁數： | 6/18頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP LP DUAL ULT LN 10-MSOP |
| 標準包裝： | 2,500 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 268 V/µs |
| 增益帶寬積： | 800MHz |
| 電流 - 輸入偏壓： | 25µA |
| 電壓 - 輸入偏移： | 300µV |
| 電流 - 電源： | 30mA |
| 電流 - 輸出 / 通道： | 130mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 5 V，±1.5 V ~ 2.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
14
FN6262.1
March 30, 2007
Applications Information
Product Description
The ISL55190 and ISL55290 are single and dual high
speed, voltage feedback amplifiers designed for fast pulse
applications, as well as communication and imaging systems
that require very low voltage and current noise. Both devices
are stable at a minimum gain of 5 and feature low distortion
while drawing moderately low supply current. The ISL55190
and ISL55290 use a classical voltage-feedback topology,
which allows them to be used in a variety of high speed
applications where current-feedback amplifiers are not
appropriate due to restrictions placed upon the feedback
element used with the amplifier.
Enable/Power-Down
Both devices can be operated from a single supply with a
voltage range of +3V to +5V, or from split ±1.5V to ±2.5V.
The logic level input to the ENABLE pins are TTL compatible
and are referenced to the -V terminal in both single and split
supply applications. The following discussion assumes
single supply operation.
The ISL55190 uses a logic “0” (<0.8V) to disable the
amplifier and the ISL55290 uses a logic “1” (>2V) to disable
its amplifiers. In this condition, the output(s) will be in a high
impedance state and the amplifier(s) current will be reduced
to 21A. The ISL55190 has an internal pull-up on the EN pin
and is enabled by either floating or tying the EN pin to a
voltage >2V. The ISL55290 has internal pull-downs on the
EN pins and are enabled by either floating or tying the EN
pins to a voltage <0.8V. The enable pins should be tied
directly to their respective supply pins when not being used
(EN tied to -V for the ISL55290 and EN tied to +V for the
ISL55190).
Current Limiting
The ISL55190 and ISL55290 have no internal current-
limiting circuitry. If the output is shorted, it is possible to
exceed the Absolute Maximum Rating for output current or
power dissipation, potentially resulting in the destruction of
the device.
Power Dissipation
It is possible to exceed the +125°C maximum junction
temperatures under certain load and power-supply
conditions. It is therefore important to calculate the
maximum junction temperature (TJMAX) for all applications
to determine if power supply voltages, load conditions, or
package type need to be modified to remain in the safe
operating area. These parameters are related using
Equation 1:
where:
PDMAXTOTAL is the sum of the maximum power
dissipation of each amplifier in the package (PDMAX)
PDMAX for each amplifier can be calculated using
Equation 2:
where:
TMAX = Maximum ambient temperature
θ
JA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Supply voltage
IMAX = Maximum supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the
application
RL = Load resistance
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Low
impedance ground plane construction is essential. Surface
mount components are recommended, but if leaded
components are used, lead lengths should be as short as
possible. The power supply pins must be well bypassed to
reduce the risk of oscillation. The combination of a 4.7F
tantalum capacitor in parallel with a 0.01F capacitor has
been shown to work well when placed at each supply pin.
For good AC performance, parasitic capacitance should be
kept to a minimum, especially at the inverting input. When
ground plane construction is used, it should be removed
from the area near the inverting input to minimize any stray
capacitance at that node. Carbon or Metal-Film resistors are
acceptable with the Metal-Film resistors giving slightly less
peaking and bandwidth because of additional series
inductance. Use of sockets (particularly for the SOIC
package) should be avoided if possible. Sockets add
parasitic inductance and capacitance which, will result in
additional peaking and overshoot.
For inverting gains, this parasitic capacitance has little effect
because the inverting input is a virtual ground, but for non-
inverting gains, this capacitance (in conjunction with the
feedback and gain resistors) creates a pole in the feedback
path of the amplifier. This pole, if low enough in frequency,
has the same destabilizing effect as a zero in the forward
open-loop response. The use of large-value feedback and
gain resistors exacerbates the problem by further lowering
the pole frequency (increasing the possibility of oscillation).
T
JMAX
T
MAX
θ
JAxPDMAXTOTAL
()
+
=
(EQ. 1)
PD
MAX
2*V
S
I
SMAX
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
(EQ. 2)
ISL55190, ISL55290
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2051IMS10#TRPBF | IC OPAMP ZERO DRIFT DUAL 10MSOP |
| LTC2051IMS10#TR | IC OPAMP ZERO DRIFT DUAL 10MSOP |
| 5146139-5 | 06 MODII HORZ SR CE 100CL |
| LTC6911IMS-1#TR | IC PGA DIGITAL R-R DUAL 10MSOP |
| 0459851363 | CONN HEADER 10PWR 32SGL 1.57MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL55291 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single and Dual Ultra-Low Noise, Ultra-Low Distortion, Rail-to-Rail, Low Power Op Amp |
| ISL55291EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL55291 EVALUATION BOARD 1 - ROHS COMPLIANT - MSOP - Bulk |
| ISL55291IUZ | 功能描述:IC OPAMP LP DUAL ULT LN 10-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| ISL55291IUZ-T13 | 功能描述:IC OPAMP LP DUAL ULT LN 10-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| ISL5571A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Access High Voltage Switch |
發布緊急采購，3分鐘左右您將得到回復。