- 您現在的位置：買賣IC網 > PDF目錄16352 > ISL54208EVAL1Z (Intersil)EVALUATION BOARD FOR ISL54208 PDF資料下載
參數資料
| 型號： | ISL54208EVAL1Z |
| 廠商： | Intersil |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION BOARD FOR ISL54208 |
| 標準包裝： | 1 |
| 主要目的： | 接口，模擬和數字式開關 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ISL54208 |
| 主要屬性： | 2 x SPDT 音頻，USB 和視頻開關 |
| 次要屬性： | 1.8 V ~ 5.5 V 電源 |
| 已供物品： | 板 |
9
FN6410.0
December 18, 2006
audio/video playback are intended to be mutually exclusive
operations.
NC1 and NC2 Audio/Video Switches
The two NC (normally closed) audio/video switches (NC1,
NC2) are 3
Ω switches that can pass signals that swing
below ground by as much as 1.5V. They were designed to
pass ground reference audio signals and dc restored
composite base-band signals (CVBS) including negative
synchronizing pulse with minimal insertion loss and very low
distortion and degradation.
The -3dB bandwidth into 75
Ω is 338MHz (Figure 17).
Crosstalk between NC1 and NC2 @ 4MHz is -78dB
(Figure 16) which allows composite video to be routed
through one switch and mono-audio through the other switch
with little interference.
The recommended maximum signal range is from -1.5V to
1.5V. You can apply positive signals greater than 1.5V but
the rON resistance of the switch increases rapidly above
1.5V. The signal should not be allowed to exceed the VDD
rail or swing more negative than -1.5V.
Over a signal range of ±1V (0.707Vrms) with VDD >2.7V,
these switches have an extremely low rON resistance
variation. They can pass a ground referenced audio signal
with very low distortion (<0.06% THD+N) when delivering
15.6mW into a 32
Ω headphone speaker load. See Figures
NTSC color bar signal at both the input (Figure 8) and output
(Figure 9) of the ISL54208. The plots show that except for a
little attentuation, due to switch RON and test fixture cabling,
there is virtually no degradation of the video waveform
through the switch.
Figure 18 shows the differential gain (DG) and differential
phase (DP) plots at the output of the switch using an actual
NTSC composite video signal and a VM700A Video
Measurement Test Set. DG = 0.28% and DP = 0.04deg.
The NC switches are uni-directional switches. The
audio/video sources should be connected at the NC side of
the switch (pins 7 and 8) and the speaker load and video
receiver should be connected at the COM side of the switch
(pins 3 and 4).
The NC switches are active (turned ON) whenever the IN
voltage is ≤ to 0.5V and the CTRL voltage to ≥1.4V.
Note: Whenever the NC switches are ON the USB
transceiver drivers need to be in the high impedance state or
static high or low state.
NO1 and NO2 USB Switches
The two NO (normally open) USB switches (NO1, NO2) are
5
Ω bidirectional switches that were designed to pass high-
speed USB differential signals in the range of ±0V to 400mV.
These switches have low capacitance and high bandwidth to
pass USB high-speed signals (480Mbps) with minimum
edge and phase distortion to meet high-speed USB 2.0 high-
speed signal quality specifications. See Figure 14 for High-
speed Eye Pattern taken with switch in the signal path.
The maximum signal range for the USB switches is from
-1.5V to VDD. The signal voltage at NO1 and NO2 should
not be allow to exceed the VDD voltage rail or go below
ground by more than -1.5V.
The NO switches are active (turned ON) whenever the IN
voltage is to ≥1.4V.
Note: Whenever the NO switches are ON the audio and
video drivers need to be at ac or dc ground or floating to
keep from interfering with the data transmission.
FIGURE 8. VECTOR-SCOPE PLOT BEFORE SWITCH
FIGURE 9. VECTOR-SCOPE PLOT AFTER SWITCH
ISL54208
相關PDF資料 |
PDF描述 |
|---|---|
| PCMB104T-R56MT | COIL .56 UH POWER CHOKE 20% SMD |
| MIC6315-31D4UY TR | IC RESET GEN 3.08V VTH SOT143-4 |
| HMC05DRAH | CONN EDGECARD 10POS R/A .100 SLD |
| CW160808-R12J | INDUCTOR 120NH 0603 SMD |
| 6435094-1 | MT-RJ TO ST LAUNCH LEAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54208IRUZ-T | 功能描述:IC SWITCH USB/CVBS/AUDIO 10-TQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54208IRZ | 功能描述:IC SWITCH USB/CVBS/AUDIO 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54208IRZ-T | 功能描述:IC SWITCH USB/CVBS/AUDIO 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54209 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:MP3/USB 2.0 High Speed Switch with Negative Signal Handling and Low Power Shutdown |
| ISL54209EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL54209 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。