- 您現在的位置：買賣IC網 > PDF目錄16359 > ISL54207EVAL1Z (Intersil)EVALUATION BOARD FOR ISL54207 PDF資料下載
參數資料
| 型號： | ISL54207EVAL1Z |
| 廠商： | Intersil |
| 文件頁數： | 2/14頁 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR ISL54207 |
| 標準包裝： | 1 |
| 主要目的： | 接口，模擬和數字式開關 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ISL54207 |
| 主要屬性： | 2 x SPDT 音頻，USB 和視頻開關 |
| 次要屬性： | 2.7 V ~ 3.6 V 電源 |
| 已供物品： | 板 |
10
FN6403.0
December 5, 2006
USB Mode
If the VBUS pin = Logic “1” and CTRL pin = Logic “0” or
Logic “1,” the part will go into USB mode. In USB mode, the
NO1 and NO2 5
Ω switches are ON and the NC1 and NC2
3
Ω audio switches are OFF (high impedance). When a USB
cable from a computer or USB hub is connected at the
common connector, the voltage at the VBUS pin will be
driven to be in the range of 4.4V to 5.25V. The ISL54207 part
will go into the USB mode. In USB mode, the computer or
USB hub transceiver and the media player USB transceiver
are connected and digital data will be able to be transmitted
back and forth.
When the USB cable is disconnected, the ISL54207
automatically turns the NO1 and NO2 switches OFF.
Low Power Mode
If the VBUS pin = Logic “0” and CTRL pin = Logic “0,” the
part will be in the Low Power mode. In the Low Power mode,
the NCx switches and the NOx switches are OFF (high
impedance). In this state, the device draws typically 1nA of
current.
EXTERNAL VBUS SERIES RESISTOR
The ISL54207 contains a clamp circuit between VBUS and
VDD. Whenever the VBUS voltage is greater than the VDD
voltage by more than 2.55V, current will flow through this
clamp circuitry into the VDD power supply bus.
During normal USB operation, VDD is in the range of 2.7V to
3.6V and VBUS is in the range of 4.4V to 5.25V. The clamp
circuit is not active and no current will flow through the clamp
into the VDD supply.
In a USB application, the situation can exist where the V
voltage from the computer could be applied at the VBUS pin
before the VDD voltage is up to its normal operating voltage
range and current will flow through the clamp into the VDD
power supply bus. This current could be quite high when
VDD is OFF or at 0V and could potentially damage other
components connected in the circuit. In the application
circuit, a 22kΩ resistor has been put in series with the VBUS
pin to limit the current to a safe level during this situation.
It is recommended that a current limiting resistor in the range
of 10kΩ to 50kΩ be connected in series with the VBUS pin. It
will have minimal impact on the logic level at the VBUS pin
during normal USB operation and protect the circuit during
the time VBUS is present before VDD is up to its normal
operating voltage.
Note: No external resistor is required in applications where
VBUS will not exceed VDD by more than 2.55V.
POWER
The power supply connected at VDD (pin 1) provides power
to the ISL54207 part. Its voltage should be kept in the range
of 2.7V to 3.6V when used in a USB/Audio/Video application
to ensure you get proper switching when the VBUS voltage is
at its lower limit of 4.4V.
Typical Performance Curves TA = +25°C, Unless Otherwise Specified
FIGURE 10. THD+N vs SUPPLY VOLTAGE vs FREQUENCY
FIGURE 11. THD+N vs SIGNAL LEVELS vs FREQUENCY
THD+
N
(%)
FREQUENCY (Hz)
20
200
2k
20k
0.04
0.05
0.06
0.07
0.08
0.09
0.1
0.11
VDD = 2.6V
VDD = 2.7V
VDD = 3.6V
VDD = 3V
RLOAD = 32Ω
VLOAD = 0.707VRMS
THD+
N
(%)
FREQUENCY (Hz)
20
200
2k
20k
RLOAD = 32Ω
VDD = 3V
0
0.1
0.2
0.3
0.4
2VP-P
1VP-P
3VP-P
2.5VP-P
ISL54207
相關PDF資料 |
PDF描述 |
|---|---|
| REC15-1212S/H2 | CONV DC/DC 15W 12VIN 12VOUT |
| LK10052R2K-T | INDUCTOR MULTILAYER 2.2UH 0402 |
| A8MMS-6018M | ADM60S/AE60M/ADM60S |
| REC15-1215S/H2 | CONV DC/DC 15W 12VIN 15VOUT |
| A6MMS-6018M | IDC CABLE - ADM60S/AE60M/ADM60S |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54207IRUZ-T | 功能描述:IC SWITCH USB/CVBS/AUDIO 10-TQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54207IRZ | 功能描述:IC SWITCH USB/CVBS/AUDIO 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54207IRZ-T | 功能描述:IC SWITCH USB/CVBS/AUDIO 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54208 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Voltage, Dual SPDT, USB/CVBS/ Audio Switches, with Negative Signal Capability |
| ISL54208EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL54208 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。