- 您現在的位置：買賣IC網 > PDF目錄2081 > ISL54004IRTZ-T (Intersil)IC AMP AUDIO PWR 1.23W AB 20TQFN PDF資料下載
參數資料
| 型號： | ISL54004IRTZ-T |
| 廠商： | Intersil |
| 文件頁數： | 11/13頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 1.23W AB 20TQFN |
| 標準包裝： | 6,000 |
| 類型： | AB 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 1.23W x 1 @ 8 歐姆; 215mW x 2 @ 16 歐姆 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 特點： | 消除爆音，關機，熱保護 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 20-TQFN（4x4） |
| 封裝/外殼： | 20-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
7
FN6513.2
October 30, 2007
The “Typical Application Circuit and Block Diagram” for this
device is provided on page 6. The “Truth Table” for the
device is provided on page 2.
DC Bias Voltage
The ISL54004 has internal DC bias circuitry which DC
offsets the incoming audio signal at VDD/2. When using a 5V
supply, the DC offset will be 2.5V. When using a 3.6V supply
the DC offset will be 1.8V.
Since the signal gets biased internally at VDD/2 the audio
signals need to be AC coupled to the inputs of the device.
The value of the AC coupling capacitor depends on the low
frequency range required for the application. A capacitor of
0.22F will pass a signal as low as 7.2Hz. The formula
required to calculate the capacitor value is shown in
Equation 1:
The 100k
Ω is the impedance looking into the input of the
ISL54004 device.
BTL Speaker Amplifier
The ISL54004 contains one bridge-tied load (BTL) amplifier
designed to drive an 8
Ω speaker load differentially. The
output to the BTL amplifier are SPK+ and SPK-. The
speaker load gets connected across these terminals.
A single BTL driver consists of an inverting and non-inverting
power op amps. The AC signal out of each op amp are equal
in magnitude but 180° out-of-phase, so the AC signal at
SPK+ and SPK- have the same amplitude but are 180°
out-of-phase.
Driving the load differentially using a BTL configuration
doubles the output voltage across the speaker load and
quadruples the power to the load. In effect you get a gain of
two due to this configuration at the load as compared to
driving the load with a single-ended amplifier with its load
connected between a single amplifier’s output and GND.
The outputs of the BTL are biased at VDD/2. When the load
gets connected across the + and - terminal of the BTL the
mid supply DC bias voltage at each output gets cancelled
out eliminating the need for large bulky output coupling
capacitors.
Headphone (Single-Ended) Amplifiers
The ISL54004 contains two single-ended (SE) headphone
amplifiers for driving the left and right channels of a 32
Ω or
16
Ω headphone speakers.
One SE amplifier drives the right speaker of the headphone
and other SE amplifier drives the left speaker of the
headphone. The speaker load gets connected between the
output of the amplifier and ground.
The audio signal at the output of each SE driver is biased at
VDD/2 and unlike the BTL driver that cancels this offset due
to its differential connection, a capacitor is required at the
output of each SE drivers to remove this DC voltage from the
headphone load.
This coupling capacitor along with the resistance of the
speaker load creates a high pass filter that sets the
amplifier’s lower bandpass frequency limit. The value of this
AC coupling capacitor depends on the low frequency range
required for the application. The formula required to
calculate the capacitor value is shown in Equation 2:
For an application driving a 32
Ω headphone with a lower
frequency requirement of 150Hz the required capacitor value
is shown in Equation 3:
Use the closest standard value.
Headphone Sense Function
With a logic “1” at the HP control pin while the HO control pin
is low will activate the headphone drivers and disable the
BTL driver.
Diagram” on page 6 shows the implementation of the
headphone control function using a common headphone
jack.
The HP pin gets connected to the mechanical wiper blade of
the headphone jack. Two external resistors are required for
proper operation. A 100k
Ω pull-up resistor from the HP pin to
VDD and a 10k
Ω pull-down resistor from the jack’s audio
signal pin to GND of the jack signal pin to which the wiper is
connected. See “ISL54004 Typical Application Circuit and
When no headphone plug is inserted into the jack the
voltage at the HP pin gets set at a low voltage level due to
the 10k
Ω resistor and 100kΩ resistor divider network
connection to VDD.
When a headphone is inserted into the jack the 10k
Ω
resistor gets disconnected from the HP control pin and the
HP pin gets pulled up to VDD. Since the HP pin is now high
the headphone drivers are activated.
A microprocessor or a switch can be used to drive the HP
pin rather than using the headphone jack contact pin.
Note: With a logic “1” at the HO pin the BTL driver remains
active regardless of the voltage level at the HD pin. This
allows a headphone to be plugged into the headphone jack
without activating the HP drivers. Music will continue to play
through the internal 8
Ω speaker rather than the headphones.
C
1
6.28
() f
() 100k
()
[]
-----------------------------------------------
≥
(EQ. 1)
C
1
6.28
() f
() Rspeaker
()
[]
--------------------------------------------------------------
≥
(EQ. 2)
C
1
6.28
() 150
() 32
()
[]
------------------------------------------------
≥
33
μF
=
(EQ. 3)
ISL54004
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54006IRTZ | IC AMP AUDIO PWR 1.23W AB 20TQFN |
| ISL55033IRTZ | IC GAIN BLOCK R-R 400MHZ 12TQFN |
| ISL55036IRTZ-T13 | IC AMP FIXED GAIN 400MHZ 24-TQFN |
| ISL55143IRZ | IC COMP CMOS HS 18V 36-TQFN |
| ISL59110IEZ-T7 | IC VIDEO DRIVER 8MHZ R-R SC70-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54005 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Integrated Audio Amplifier Systems |
| ISL54005IRTZ | 功能描述:IC AMP AUDIO PWR 1.23W AB 20TQFN RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| ISL54005IRTZ-T | 功能描述:IC AMP AUDIO PWR 1.23W AB 20TQFN RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| ISL54006 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Integrated Audio Amplifier Systems |
| ISL54006IRTZ | 功能描述:IC AMP AUDIO PWR 1.23W AB 20TQFN RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
發布緊急采購，3分鐘左右您將得到回復。