- 您現在的位置：買賣IC網 > PDF目錄16908 > ISL28207SOICEVAL2Z (Intersil)EVAL BOARD FOR ISL28207 8SOIC PDF資料下載
參數資料
| 型號： | ISL28207SOICEVAL2Z |
| 廠商： | Intersil |
| 文件頁數： | 13/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR ISL28207 8SOIC |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1 |
| 每 IC 通道數： | 2 - 雙 |
| 放大器類型： | 通用 |
| 輸出類型： | 單端 |
| 轉換速率： | 0.32 V/µs |
| 電流 - 輸出 / 通道： | 40mA |
| 工作溫度： | -40°C ~ 125°C |
| 電流供應（主 IC）： | 210µA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 40 V，±2.25 V ~ 20 V |
| 板類型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL28207 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
ISL28107, ISL28207, ISL28407
20
FN6631.7
February 25, 2013
The resistor-ESD diode configuration enables a wide differential
input voltage range equal to the lesser of the Maximum Supply
Voltage in the “Absolute Maximum Ratings” on page 6 (42V), or a
maximum of 0.5V beyond the V+ and V- supply voltage. The
internal protection resistors eliminate the need for external input
current limiting resistors in unity gain connections and other
circuit applications where large voltages or high slew rate signals
are present. Although the amplifier is fully protected, high input
slew rates that exceed the amplifier slew rate (±0.32V/s) may
cause output distortion.
Output Current Limiting
The output current is internally limited to approximately ±40mA
at +25°C and can withstand a short circuit to either rail as long
as the power dissipation limits are not exceeded. This applies to
only one amplifier at a time for the dual op-amp. Continuous
operation under these conditions may degrade long-term
reliability.
Output Phase Reversal
Output phase reversal is a change of polarity in the amplifier
transfer function when the input voltage exceeds the supply
voltage. The ISL28107, ISL28207 and ISL28407 are immune to
output phase reversal, even when the input voltage is 1V beyond
the supplies.
Unused Channels
If the application only requires one channel, the user must
configure the unused channels to prevent them from oscillating.
The unused channels can oscillate if the input and output pins
are floating. This results in higher than expected supply currents
and possible noise injection into the channel being used. The
proper way to prevent this oscillation is to short the output to the
inverting input and ground the positive input, as shown in
Figure 55.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power supply conditions. It
is therefore important to calculate the maximum junction
temperature (TJMAX) for all applications to determine if power
supply voltages, load conditions, or package type need to be
modified to remain in the safe operating area. These parameters
are related using Equation 1:
where:
PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
PDMAX = Maximum power dissipation of one amplifier
VS = Total supply voltage
IqMAX = Maximum quiescent supply current of one amplifier
VOUTMAX = Maximum output voltage swing of the application
RL = Load resistance
ISL28107, ISL28207, ISL28407 SPICE Model
the net list for the ISL28107, ISL28207 and ISL28407 SPICE
model. The model is a simplified version of the actual device and
simulates important AC and DC parameters. AC parameters
incorporated into the model are: 1/f and flatband noise, Slew
Rate, CMRR, Gain and Phase. The DC parameters are VOS, IOS,
total supply current and output voltage swing. The model uses
typical parameters given in the “Electrical Specifications” table
dominant pole at 0.01Hz. CMRR is set (145dB, fcm = 100Hz). The
input stage models the actual device to present an accurate AC
representation. The model is configured for ambient temperature
of +25°C.
results for the Noise Voltage, Closed Loop Gain vs Frequency,
Closed Loop Gain vs RL, Large Signal Step Response, Open Loop
Gain Phase and Simulated CMRR vs Frequency.
License Statement
The information in this SPICE model is protected under the
United States copyright laws. Intersil Corporation hereby grants
users of this macro-model hereto referred to as “Licensee”, a
nonexclusive, nontransferable licence to use this model as long
as the Licensee abides by the terms of this agreement. Before
using this macro-model, the Licensee should read this license. If
the Licensee does not accept these terms, permission to use the
model is not granted.
The Licensee may not sell, loan, rent, or license the macro-model,
in whole, in part, or in modified form, to anyone outside the
Licensee’s company. The Licensee may modify the macro-model
to suit his/her specific applications, and the Licensee may make
copies of this macro-model for use within their company only.
This macro-model is provided “AS IS, WHERE IS, AND WITH NO
WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED,
INCLUDING BUY NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.”
In no event will Intersil be liable for special, collateral, incidental, or
consequential damages in connection with or arising out of the
use of this macro-model. Intersil reserves the right to make
changes to the product and the macro-model without prior notice.
FIGURE 55. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
-
+
T
JMAX
T
MAX
θ
JAxPDMAXTOTAL
+
=
(EQ. 1)
PD
MAX
V
S
I
qMAX
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
(EQ. 2)
相關PDF資料 |
PDF描述 |
|---|---|
| 500C362T450DD2B | CAP ALUM 3600UF 450V SCREW |
| 202D163-3-60-0 | BOOT MOLDED |
| VI-JTV-EY | CONVERTER MOD DC/DC 5.8V 50W |
| MIC2077-2BM | IC USB DISTRIB SW QUAD 16-SOIC |
| ISL28114SOT23EVAL1Z | EVALUATION BOARD FOR ISL28114 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL28208 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:40V Precision Single Supply Rail-Rail Output Low Power Operational Amplifiers |
| ISL28208FBZ | 功能描述:IC OPAMP PREC RR 1.2MHZ DL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:2.1 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:2000µV 電流 - 電源:750µA 電流 - 輸出 / 通道:16mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 16 V，±1.35 V ~ 8 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-10529-1 |
| ISL28208FBZ-T13 | 功能描述:IC OPAMP PREC RR 1.2MHZ DL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:2.1 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:2000µV 電流 - 電源:750µA 電流 - 輸出 / 通道:16mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 16 V，±1.35 V ~ 8 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-10529-1 |
| ISL28208FBZ-T7 | 功能描述:IC OPAMP PREC RR 1.2MHZ DL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:2.1 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:2000µV 電流 - 電源:750µA 電流 - 輸出 / 通道:16mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 16 V，±1.35 V ~ 8 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-10529-1 |
| ISL28208FBZ-T7A | 功能描述:精密放大器 ISL28208FBZ 40V LW N RAIL OUT SNG SUPP RoHS:否 制造商:Maxim Integrated 每芯片的通道數量: 輸入補償電壓:0.25 mV at +/- 5 V 輸入電壓范圍（最大值）: 安裝風格: 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。