- 您現在的位置：買賣IC網 > PDF目錄3408 > ISL28113FHZ-T7 (Intersil)IC OPAMP GP RRIO 2MHZ SOT23-5 PDF資料下載
參數資料
| 型號： | ISL28113FHZ-T7 |
| 廠商： | Intersil |
| 文件頁數： | 23/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP GP RRIO 2MHZ SOT23-5 |
| 標準包裝： | 3,000 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 1 V/µs |
| 增益帶寬積： | 2MHz |
| 電流 - 輸入偏壓： | 3pA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 90µA |
| 電流 - 輸出 / 通道： | 22mA |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁
ISL28113, ISL28213, ISL28413
9
FN6728.7
November 15, 2012
Applications Information
Functional Description
The ISL28113, ISL28213 and ISL28413 are single, dual and
quad, CMOS rail-to-rail input, output (RRIO) micropower
operational amplifiers. They are designed to operate from single
supply (1.8V to 5.5V) or dual supply (±0.9V to ±2.75V). The parts
have an input common mode range that extends 100mV above
and below the power supply voltage rails. The output stage can
swing to within 15mV of the supply rails with a 10k load.
Input ESD Diode Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails (see “Pin Descriptions -
Circuit 1” on page 3). For applications where the input voltage
may exceed either power supply voltage by 0.5V or more, an
external series resistor must be used to ensure the input currents
never exceed 20mA (see Figure 19).
Output Phase Reversal
Output phase reversal is a change of polarity in the amplifier
transfer function when the input voltage exceeds the supply
voltage. The ISL28113, ISL28213 and ISL28413 are immune to
output phase reversal, even when the input voltage is 1V beyond
the supplies.
Unused Channels
If the application requires less than all amplifiers one channel,
the user must configure the unused channel(s) to prevent it from
oscillating. The unused channel(s) will oscillate if the input and
output pins are floating. This will result in higher than expected
supply currents and possible noise injection into the channel
being used. The proper way to prevent this oscillation is to short
the output to the inverting input and ground the positive input (as
shown in Figure 20).
Power Dissipation
It is possible to exceed the +125°C maximum junction
temperatures under certain load, power supply conditions and
ambient temperature conditions. It is therefore important to
calculate the maximum junction temperature (TJMAX) for all
applications to determine if power supply voltages, load
conditions, or package type need to be modified to remain in the
safe operating area. These parameters are related using
Equation 1:
where:
PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Total supply voltage
IqMAX = Maximum quiescent supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the application
RL = Load resistance
ISL28113, ISL28213 and ISL28413 SPICE
Model
the net list for the SPICE model. The model is a simplified version
of the actual device and simulates important AC and DC
parameters. AC parameters incorporated into the model are: 1/f
and flatband noise, Slew Rate, CMRR, Gain and Phase. The DC
parameters are IOS, total supply current and output voltage swing.
The model uses typical parameters given in the “Electrical
Specifications” Table beginning on page 4. The AVOL is adjusted
for 85dB with the dominate pole at 100Hz. The CMRR is set 72dB,
f = 35kHz). The input stage models the actual device to present an
accurate AC representation. The model is configured for ambient
temperature of +25°C.
results for the Noise Voltage, Closed Loop Gain vs Frequency,
Large Signal 5V Step Response, CMRR and Open Loop Gain
Phase.
FIGURE 19. INPUT ESD DIODE CURRENT LIMITING
-
+
RIN-
RL
VIN-
V+
V-
RIN+
RF
RG
FIGURE 20. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
-
+
T
JMAX
T
MAX
θ
JAxPDMAXTOTAL
+
=
(EQ. 1)
PD
MAX
V
S
I
qMAX
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
(EQ. 2)
相關PDF資料 |
PDF描述 |
|---|---|
| 961124-6700-AR-PR | CONN HEADER VERT 24POS GOLD SMD |
| 3428-25K2 | CONN HEADER 20PS STR SHORT LATCH |
| CS702025Z | THERMOSTAT 20 DEG C N/C FASTON |
| 151244-8322-TH | CONN HEADER 2MM 44PS DL T/H 15AU |
| 77313-118-18 | HDR STR DR.100 DP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL28113FHZ-T7A | 功能描述:放大器 IC 開發工具 ISL28113FHZ SINGLE GEN PURPSE MIPR RRIO RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| ISL28113SOT23EVAL1Z | 功能描述:放大器 IC 開發工具 ISL28113 EVAL BRD 1 RHS CMPL5LD RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| ISL28114 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single, Dual, Quad General Purpose Micropower, RRIO Operational Amplifiers |
| ISL28114_11 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single, Dual, Quad General Purpose Micropower, RRIO Operational Amplifiers |
| ISL28114FEZ-T7 | 功能描述:放大器 IC 開發工具 ISL28114FEZ SINGLE GEN PURPSE MIPR RRIO RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。